Jump to content

All Activity

This stream auto-updates

  1. Past hour
  2. Burger
    well the BCM thing didn't quite work out, but i got some very nice domino units instead. they were a bit cheaper than the other thing and still give me all the features i wanted, so it's all good. new MCs as well: new bars all set up: (was quite the relief to hook the switch blocks up and not blow any fuses or let any magic smoke out, all the buttons even work to boot including the ones that weren't there before) this digital flasher i've had laying around for like 8 years finally came in handy. chain and sprockets also on, swingarm's all back together: now some bad news. with the clutch SC back on, i decided it was finally time to start it. threw some fresh plugs at it, mashed the go button, it cranked, and...nothing. it did bark with some starter fluid, at which point it made oil pressure and showed no signs of leaks, but it wouldn't stay running. when i looked down the throttles, nothing was coming out the injectors. then i pulled off the return line and cycled the key to check fuel flow, which checked out just fine (which it damn well should, since i changed out almost the entire fuel system). so the injectors got gummed up. which means i gotta pull off the throttle bodies. son of a bitch. i think what i'm gonna do is pull the injectors out of the old motor and see if they'll come back to life, so i can just get the actual swap all done at once.
  3. Today
  4. Lorne
    Is it possible the key is bent or twisted? Do you have a second key you could try? Graphite is the better choice for lubrication, too bad it wasn't your solution.
  5. Lorne
    I've never felt the need to change from the stock screen on any of my VFRs - 3rd, 5th, and now 6th gen. Just enough air gets past to take some weight off my arms, and the airstream is pretty smooth. People come in all shapes and sizes, and they wear different jackets and helmets, so not everyone will like Honda's screen.
  6. Gaz66
    https://www.ngkpartfinder.co.uk/assets/Uploads/2019-Plug-Covers-ver3.pdf Here ya go, have a butchers at this, shows part numbers, check against what's fitted on your bike, yes plugs & caps must be resistor type.
  7. LloydG
    So the stock rear is 130 70 18. I can a Bridgestone bt46 130 80 18 for a really good price.Does anyone run this tyre on the nc21 and will that slightly higher sidewall work witj clearance etc.
  8. mello dude
    Whoa... you got quite the journey there! Best Wishes!
  9. natnif
    A few weeks with not much happening A few weeks with not too much happening as I turned my attention to other things but I did make a bit of progress....at least with diagnosing issues! When I put all back together a few weeks back it ran, but not happily. So! new plugs are ordered (will be here Saturday) and I've also sourced some vacuum hose to replace everything as lots are cracked or at the very least well dried out and waiting to crack. It would settle to a very high idle (4-5k) while it was warming up, so I figured I better look at the wax idle unit. I drained the coolant and popped off the hose which revealed some nasty white powdery gunk so I'm guessing someone has just had water in there which has oxidised. I'd say flow was at least partially blocked to the wax idle unit. while I was in there, I also realised the starter valves are fairly rusty looking and just aren't moving freely at all so I've ordered a good second hand throttle body which should take care of all of that. Now that I think about it I should probably test the thermostat while I'm in that far. Tomorrow if the weather is on my side I'll sort the rear brakes and loosen the throttle bodies off so that when the "new" ones arrive, I can just get on wioth putting it back together. Hopefully all those jobs will see her running properly in the next week or two. Oh, and it looks like I have an oil leak to sort too. Brilliant!
  10. LloydG
    So will the Bridgestone bt46 with the slightly higher wall fit and work on tje rear of the vfr400r nc21.I can get ot for much cheaper and better quality than the 130 70 18 that's available
  11. mello dude
    Photos... Hope this helps! Rubber shield and Tank Bracket.. Starter Solenoid Circuit Btw - You miight review my thread on Thermostat/hoses/brakes for ideas
  12. Gaz66
    Single Fuse holder above⬆is upside down. Did u inspect the female terminals in the plug? Prone to becoming loose when plugs been off a few times, causes a weak connection/high resistance, terminals lose their springiness & don't grab the male terminals in the relay enough, replaced loads of melt down plugs & relays, often cooks the loom making wiring stiffer than a porn stars 🐓 which needs cutting out & replacing too. If plug's good it's worth squeezing females back together with a small straight bladed driver for a snug fit onto males. New plug/terminal kits are available as a pattern part should the need arise, I always keep a few in stock for customers.👍
  13. fabio222
    All of our spins have different purposes. Clearing our heads, hearing the roar of a V4, or just getting to work in the morning. This spin was my first since Christmas that didn't involve it ending, or starting, in the workplace carpark. This was going to be just me and my VFR heading on down to Long Strand to write a name in the sand, gaze out to the sea for a while, and then, wiping a tear from my eye, saying goodbye. Baby Croí would've been 3 years old last week and around this time every year since, I travel the hour or two to this beach where we said our goodbyes. This year I was going on my own so it was a great excuse to bring the bike and let that be part of my journey. It had been so long since my last spin, having a toddler will do that to ya, that I noticed my reactions and attention span weren't quite what they should be. I had a couple of warnings early in the spin where I went in a little too hot to a bend, or I didn't see a car at a junction (not that it pulled out but I'd pass it thinking "didn't see him there"). I tried harder to concentrate and tried to relax myself on the bike, my muscles used to the 30 minute commute but far less used to anything longer or twistier. Sweeping past the city and down towards west Cork, the scenery changes in front of you. It becomes more hilly, a little more rugged the further west you go, and especially as you towards the coast. Some of the roads are deceiving, they look smooth but are actually rutted and slap you around on the bike but then you come across twisty bits taken anywhere between 50kph and 80kph and the bike is a joy. It has so much mechanical grip that I always feel I could have been faster and it rewards you for riding well. Holding a gear rather than dancing through the gearbox is perfect on these bits, the VTEC coming on song as you exit a corner, waking up the locals. Reaching my destination, the beach is busy, and a lot of people take a second look at the bright red machine that has just rumbled into their midst. I step off of the bike, leave my helmet and gloves on the tank, and walk to the edge of the water. In the sand, I spell out her name, draw a heart, and take in the emotion. The sound of the sea in front of me is calming and, my moment of reflection over, I walk back towards the bike. I'm pretty hungry now so I get fish and chips. It fills me but it's disappointingly small for the price paid. Still, I got a great view of the sea and some extra time to think. Back on the bike, I turn for home, and end up following a guy on a little Honda Dax 125, a bit like the Grom. His lines are perfect through the bendy bits, making up for the lack of power on any straights but I'm never bored behind him. Eventually we part ways and, by now, my body is really not used to this and the last 40 minutes are a little uncomfortable. I can only imagine what a full-on head-down, bum-up sportsbike would be like for someone of my size, short limbs, wide shoulders. Still, the VFR has been a worthy companion. It's been immensely fun, it's encouraged me to ride my best, and it's brought me home. Couple of pics: https://ibb.co/5gVqMP3z https://ibb.co/FkQ9Kyrv
      • 2
      • Like
  14. fabio222
    Have an MRA Vario. It's handy because you can adjust it easily but I tend it leave it in the "up" position so there's less wind hitting me. I don't think it does much for noise though.
  15. Mohawk
    Check the slot cover, ham fisted use when inserting the key can bend the soft metal surrounds & jam the slot cover. You can usually straighten it all out with a thin flat blade screwdriver to lever the bent metal up which frees the stuck slot cover. Then squirt some silicone spray or WD40/GT85 etc into the lock mechanism through the key slot. Then work the key a few times to distribute the lube.
  16. Skids
    I've used WD40 previously on another bike, which worked, but I dont know if it is the best thing to use.
  17. Burger
    data point of one and not at all the same bike, but the stock fan on my sv650 was just downright not up to task for texas summers; if i was standing still, the temp would climb even if the fan was on. swapping it out for a 5" spal fan fixed that problem. (at first i had a pair of them but that turned out to be way overkill.) the vfr fan looks to be similarly constructed, so i wouldn't be surprised at all if the root cause of everyone's overheating issues is just a wimpy fan. i still have that second fan laying around somewhere, so before my bike's finished i plan to slap it on so i can see how it performs.
  18. Terry
    A question for the Hive Mind. The ignition switch is not quite right. Once the key is in and pressed, I can rotate the key easily, but then it is not easy to retract, feels kind of sticky, and I have to work it back/forth until it releases and can be pulled out. I have dusted some graphite powder into the lock but I don't think that really changed much. I feel that I should be spraying some sort of solvent in there to wash out whatever is making the lock sticky. Any suggestions? I am thinking of WD40 or penetrating oil.
  19. Yesterday
  20. davenay67
    Keep it apart....I'm sure to run into many other 'how does it go back?' questions. 🤣
  21. BusyLittleShop
    If you see *continuous* temps higher than 220ºF or below 180ºF then trouble shooting is in order: Continuous engine temps above 220ºF or 104ºC is also a problem and the proper order of items to trouble shoot are: 1)Faulty radiator cap... system should hold 1.1 pressure ratio... 2)Insufficient coolant... 3)Passages blocked in the radiator, hose or water jacket... 4)Air in the system... 5)Thermostat stuck closed... 6)Faulty temp meter or thermo sensor... 7)Faulty fan... 8)Faulty fan switch... Engine temps below 180ºF or 82ºC is an problem... it means that the moisture produced during combustion is not getting hot enough to evaporate out the pipe as steam... instead that moisture will migrate to the oil and produce a milky white contamination... Note normal by products of combustion is water... . Every gallon of gas creates roughly 8 pounds of water vapor... we all have witnessed water escaping out of tail pipes on cold mornings... The sequence of events to trouble shoot are: 1)Faulty temp meter... 2)Thermostat stuck open... 3)Faulty fan switch... (stuck on) Leaky Head Gasket Check... You can visual inspect for a leaking head gasket by pulling the spark plugs and peering down each hole... if the top of the piston is black then no leak that cylinder... if the top of the piston is a bright shiny aluminum then leak detected... because a leaky head gasket allows coolant in and that produces steam under the heat of combustion... the net effect is a super clean piston dome and no nasty black... On bike Thermostat Check To check if the thermostat is opening start the engine at its lowest temp... open the rad cap... observe at what temp the coolant begins to flow... if the temp rises above 180F and the coolant does not flow then your thermostat is suspect To trouble shoot an oil leak start by tracing the wet trail back to its the highest point to determine the origin... if the origin is mid cylinder then investigate a possible blow head gasket... take a compression test to verify the effective cylinder..
  22. mello dude
    Hang on... Mine's apart... I'll get a photo of mine and post it tomorrow.
  23. davenay67
    Not what I was wanting to hear, but I appreciate the input. 🙂 The wiring seems really tight, and I'm not sure turning 180 degrees is going to be all that easy. Might need to find what is preventing that.... Update: Actually quite easy once I removed the tank bracket and unplugged the top cable. Much better.
  24. Terry
    You may be able to disassemble the plug caps and check; stick a flat blade screwdriver up inside and you should be able to unscrew the end, there is usually a spring and a resistor in there that will slide out (and can be easily refitted). I did this on my 86 VFR and found the resistor was broken and was a cause of poor running. The resistor was (from memory) 5kOhm.
  25. JimMoore
    Follow-up to this thread. It's cooled off a little bit and the bike is running much cooler. I'm now convinced it was the absurd OATs + jackassery that were causing the high temperatures.
  26. airwalk
    These specs come from the past.. ‘86 vfr, 5K ohms (terminal/“cap”), ‘88 Hawk nt650, 10Kohms per terminal. Seems like there’s wrong info printed in the Hawk shop manual, as a total of 10K should result from plug(5K)+ cap/terminal(5K). My vote is to hopefully see 5K ohms when testing/measuring & call that an acceptable result..if you ever find an absolutely correct # please share
  27. Mohawk
    RC30 £132,250 RC45 £92,000 Gulp !
  28. mello dude
    I'm also a big fan of Project Farm and also Torque Test Channel.... Together, they have cost me a lot of money! 😁
  1. Load more activity

  • Blogs

    1. HispanicSlammer

      A blog by HispanicSlammer in General

      • 122
        entries
      • 565
        comments
      • 300223
        views

      Recent Entries

      HispanicSlammer

      med_gallery_491_3463_298783.jpg

      Juniper Pass

      I took a day off from work and also from my bicycle training to take out the Veefalo one last time before the weather turns ugly, supposed to snow the rest of the week and possibly start sticking to the ground along the Colorado Front Range. I took a leisurely pace up hwy 105 toward Morrison and got reacquainted with the bike since its been over a month since I took any sort of twisties on it at all, hwy 105 is a scenic ride along the front range between Denver and Colorado Springs, its mostly easy fast sweepers and lite traffic so its a favorite road of mine when going north. Then I have to negotiate a bit of traffic near Highlands ranch and up hwy 470 into the mountains. I decided to take the Morrison Exit and try either Lookout Mountain or head up Golden Gate Canyon - this time it was Lookout Mountain, I was sort of making it up on the fly as I went along. Lookout Mountain is my old bicycling haunt from my days while I was working at Coors, its a killer ride and all uphill - I don't think I could do it today If I had to, not quite there yet! I saw a whole bunch of riders doing it though and wished I was in shape enough to be there doing it as well. 30 more lbs and I will be able to do it! On this day I would do it on the Veefalo instead.

       

       

       

       

      I took a video from the gateway to the top at the Lookout Mountain State Park, getting past riders, the guy in the green jacket actually pretty much astounded me with how far he had gotten in the short time it took me to set up my camera, some 3 miles at least and up to the gateway from the turn off at hwy 6! Amazing I thought. I took the first two turns slow then got more comfortable as I went up further, till I was doing well, I made some gearing mistakes and took the tight 15mph marked hairpins in the wrong gear so I lugged it a bit on one or two. Still enjoyed it though and then got off at the top and hiked over a rock outcropping for an overview of the road for the pictures below.

       

       

      gallery_491_3463_225077.jpg

      Lookout Mountain - Golden Colorado

      gallery_491_3463_460686.jpg

      Zoomed in

      gallery_491_3463_96202.jpg

      Lookout Mountain Park top of the mountain

      From there I headed up interstate 70 to Idaho Springs for a beer at the Tommy-knockers brewery, I was the only customer in the joint - slow day for them so they treated me like a king! I got a nice tour of the place sort of impromptu, they made me a nice Pastrami sandwich on rye and with the brown ale it was fantastic. I must say the beer is much better there than in the bottles - its always good at the brewery. I am glad I stopped

      gallery_491_3463_328875.jpg

      Tommy-knockers Brewpub Idaho Springs

      gallery_491_3463_290342.jpg

      Idaho Springs Colorado

      gallery_491_3463_432219.jpg

      Mashtuns and fermenters

      gallery_491_3463_278071.jpg

      Rows of fermenters

      I finished my lunch and since the road to Mount Evans is right there I headed up Squaw pass hoping to get in some nice pictures I wasn't expecting what I found, ICE IN ALL THE SHADY PARTS

      gallery_491_3463_419309.png

      Icy patches on Squaw Pass definitely taking it easy on that road

      There were some section where the ice covered the whole road for 300 yards or so I had to roll through it with my legs out to help keep the bike from sliding and falling over, I took it real slow. A Ford pickup was right behind me so I pulled over to let him pass but the guy was going slower then even I was so I pressed on - in places where I could see I just cut over to the oncoming lane and out of the ice where the sun was shining on the road more, but some places there was not alternative so I just had to go slow, good thing it wasn't slick but rather they tossed some gravel over the worst parts so I had some traction!

      I did stop for pictures in all the best spots

      gallery_491_3463_338944.jpg

      Echo Lake at Mount Evans showing off my new plate

      gallery_491_3463_562075.jpg

      Elephant Butte Park and Denver

      gallery_491_3463_271364.jpg

      Close up

      gallery_491_3463_12419.jpg

      Veefalo on Squaw Pass

      gallery_491_3463_298783.jpg

      Juniper Pass

      gallery_491_3463_291678.jpg

      Juniper Pass

      gallery_491_3463_385846.jpg

      Mount Evans

      My route A is home B is Tommy-knockers

       

    2. MartinkaP's Blog

      A blog by martinkap in General

      • 8
        entries
      • 77
        comments
      • 36388
        views

      Recent Entries

      martinkap
      Latest Entry

      I Am Back !

      gallery_7692_2036_18129.jpg

      Not that it matters and not that I expect anyone had noticed, but to those who sent me "where are you?" I would like to say I am back. Not only that I am officially returning to VFRD after nearly 2 months break but I have also ridden my Hawk last weekend and had FUN! Let me restate that; I had major fun riding! Something I have almost given up on.

      Most of you have been riding your whole adult lives and riding is not only a hobby to you, it is part of you. But I started riding three years ago and even though I have encounter some setbacks, till this spring I loved riding with whole my heart. However, I have always considered riding as my hobby. As a hobby which suppose to make my life better, more fun and more rich. Life is too short to do something which we don't fully love.

      My love of riding received a first major scar this spring: I lost a friend on the racetrack. He was a total stranger who offered me his help after I lowsided at CMP track last year. I still remember hearing his "Hi, my name is Todd, do you need help?" while I was duct-taping my roadrash from ripped jacket. He helped me straighten up the shifter and we kept in touch. The next time we saw each other was the day he died.

      With 9 months delay, I can say that Todd's death shook me more than I have realized. It rooted fear in me which was fueled by seeing and hearing about others getting hurt over and over again. If I was to summarize this year - it would be one big accident report. I became sensitive to every broken bone, every roadrash, every lowside. And even though I did 10 track days this year, I became slower and slower and slower. Suddenly, I have acquired this 'grandma' riding style on the road, frozen with fear that behind every corner there is car standing in my lane, or major sand trap or deer staring at me ... I was crippled with fear not only for me about also for my fellow rider.

      So, at the end of this year, I rode more and more by myself. I could not bear the feelings of responsibility for others on the road and my lines were crippled by my own fears. It all culminated this fall at WDGAH. In a freaky accident Love2rideh82crash was taken down by a truck crossing into our lane. I was done. I finished the weekend, locked the VFR into a garage and took a break.

      Until the last weekend, I pretended that motorcycles do not exists. As a last instance after 2 months break from riding, I decided to go to CMP track to see if I can still have fun. I also felt like I should go for the memory of Todd. I went and I had fun! I had much more fun than I expected and the most fun on track I can remember. Suddenly the whole track connected into an uninterupted line of turns and I felt one with the bike riding around! I was giggling like a little girl in my helmet and keep on giggling ever since smile.gif

      Granted I was not the fastest one and through out the weekend, I have never exceeded about 60% of my riding abilities, but I had no "oh-shit" nor 'blond' moments. I could have maybe go faster, I could have brake later for the turns and I could have lean further, but I am no Rossi nor Stoner. I decided to ride for fun and I had amazing blast riding well within my comfort zone.

      I was proud of myself when, after bandaging Ricks arm, I was able to distance myself and go back to riding without the year-long fear. I did feel bad for him but the feelings were not crippling my lines nor my mind. And when a total stranger came to me and said "Hi, my name is Todd", my heart stopped for a minute though but I suddenly knew that my life went a full circle. I probably will never win MotoGP :idea3: , but I am back! :wheel:

×
×
  • Create New...

Important Information

By using this site, you agree to our Privacy Policy.

  I accept