Jump to content

All Activity

This stream auto-updates

  1. Past hour
  2. Terry
    It sounded like a scrape to me, not a slosh. My opinion is that it has to be something within the motor or driveline as it responds exactly to the throttle on or off. Maybe as simple as the chain being pulled tight on the top run by acceleration, then slacking off and dragging over the rubber bumper along the top of the swingarm, so I would be starting there. I guess it could be the camchain tensioners but I thought they're more likely to cause a big rattle rather than a scrape.
  3. orener
    Hi - I'm wondering if any of you have any ideas what this noise could be on my 2014 VFR800F from the attached video (got up to 10mph and pulled off the throttle, then pulled the clutch)... additional information below: It sounds a little like sloshing but is relatively loud It happens on deceleration (the second I let off the throttle, this noise comes up - and when I'm on the throttle, it goes away). When I get faster and decelerate, the noise gets louder and more aggressive as well. On start-up and idle there is no noise. It sounds like it's coming from the front of the bike (gas tank? radiator? front wheel?) I recently changed the braked pads / cleaned the calipers; when I had the bike lifted, and spun the wheel, there were no noises. Even with the brakes re-installed, very minimal noise - just normal pad contact When the brakes were off, I also checked the wheel for side-to-side play and there wasn't any - so don't think it's a wheel bearing issue The noise happens even when the clutch is pulled (the end of the clip is me pulling the clutch) - but I couldn't recreate while the bike was turned off (even trying to build some speed) Really curious if you have any ideas... would like to resolve this. Thank you! IMG_7513.mov
  4. Today
  5. orener
    Hi - I'm wondering if any of you have any ideas what this noise could be on my 2014 VFR800F from the attached video (got up to 10mph and pulled off the throttle, then pulled the clutch)... additional information below: It sounds a little like sloshing but is relatively loud It happens on deceleration (the second I let off the throttle, this noise comes up - and when I'm on the throttle, it goes away). When I get faster and decelerate, the noise gets louder and more aggressive as well. On start-up and idle there is no noise. It sounds like it's coming from the front of the bike (gas tank? radiator? front wheel?) I recently changed the braked pads / cleaned the calipers; when I had the bike lifted, and spun the wheel, there were no noises. Even with the brakes re-installed, very minimal noise - just normal pad contact When the brakes were off, I also checked the wheel for side-to-side play and there wasn't any - so don't think it's a wheel bearing issue The noise happens even when the clutch is pulled (the end of the clip is me pulling the clutch) - but I couldn't recreate while the bike was turned off (even trying to build some speed) Really curious if you have any ideas... would like to resolve this. Thank you! IMG_7513.mov
  6. FromMaine
    Wow, went out to my bike and had a look. That is in a less than ideal place. The shock is mountedleft of the weld to a plate that depends on those two mounting bolts. Obviously that is a cast aluminum part. Cast aluminum tends to be porous and difficult to weld. I would certainly check with the shop you intend to take it to to inform them what you need to do, many welders will not touch cast aluminum. That said, it can be done, as Honda welds that cast piece to an extruded aluminum spar. To the left of the weld is extruded, fairly easy to weld, the right is cast, not so easy. I certainly hope they are able to repair it. Great work getting this far!
  7. Worfje
    Any pictures of your Hel(of a braking system)?
  8. rgrattan
    I was able to fix this issue without any ABS Modulator bleed antics. It turns out the front right rotor on my VFR had a slight wobble/buckle aka runout. This meant that repeated bleeds could never fix the issue. I replaced the front rotors with OEM Honda. Costly but necessary. Now the bikes brakes feel fantastic.
  9. Worfje
    I assume you are referring to the vacuum lines that attach to the bottom part of the air box. The connection to the air box is only to 'put a plug' in the vacuum line. Looking at the complexity of the DCBS, I doubt someone will be able to guarantee that. It can certainly help in addition to the prescribed procedure. About your crack... I am surprised to see it. I hope the welding shop sees possibilities to repair this.
  10. keny
    Well no ride on Saturday even it fired up great, it peed fuel, but again letting it sit over night made wonder and today Sunday no fuel leak. Today's fuel are not good for these old bikes. So ready for a ride! So first ride was not that long, it's just +12°C and roads are at places not completely clean of gravel that is used under winter to get grip on snow as ice the roads are covered off during winter months. But my local favorite cafe was open So a stop there. And a few stops for pictures So even not perfect conditions on road it was fun! It runs like a champ but still has a knocking sound I don't like, it might come from front head, have to look into it. Also the front brake didn't feel as powerful as should, have to look into that to.
  11. keny

    Keny`s album

    Images added to a gallery album owned by keny in Member's Gallery

    Pics of my VFR and ride pics!
  12. Worfje
    Nice to hear you had a positive experience! I found the earlier posts here.
  13. vfrcapn
    I used one, works like new. Seller gave a few prototypes away here on VFRD before going to market.
  14. vfrgiving
    I understand your qualms with VTEC, but otherwise comparing the 800 with your B-King isn't really fair. There's an entire entry-level middleweight motorcycle of displacement between them. A VFR1200 would be more in the B-King's wheelhouse for cross-shopping competition. Imagine me owning a Pacific Coast and SuperDuke 1390 and comparing them (both V-Twins). "I like the storage of the PC, but prefer the effortless torque of the Duke. If I sold the Duke for a PC I would have regretted it." 😅
  15. Lorne
    Welcome to the club!
  16. Dutch724
    The only issues I had with the set of cooling hoses was when it came to the reservoir over flow hose. Was not quite long enough or thin enough to route where the old one was, but really that is no big deal. It is still a really good set of hoses. When I said extra I meant the one from the pair system, its big easy to figure out. There are a bunch of small ones and I forgot to take pictures before pulling them apart. I'm planning refering back to the factory service manual. For the ones I'm unsure of. When I flush the brakes on my older bike I used a syringe and ran the fluid backwards in through the zerk fitting and up to the fluid reservoir. No air in the system seeing I pushed them up and out. Will that not work on this bike? Yes, I like mods that provide function, reliable, and they are useful. I plan to be on the bike alot and I like to make it my own. Delinking the brakes I'm unsure of yet. I can see it useful for my dirt road that has a downhill before getting to my house. I normally use my back brake for slowing the bike down. I have included the pictures of the broken frame where the seat support on the left side is JB welded. I'm planning to get it fixed next week. When I get it to the shop I'm hoping to get pictures of the damage under the JB weld. Once I get them I will share. I am hoping the wax unit will not need any adjustment now that I have the mouse condo out. I did notice the adjustment screw is not in far enough to touch anything. Should I be concerned with that? As always thx for the help
  17. LEGEND
    I’ve never owned a Ninja 1000 but I did buy a left over Suzuki BKing in 2011. I still have my ‘07 Vfr but over the years I’ve found the Suzuki to be more reliable, much smoother and when ridden sanely gets as good and sometimes better mileage than my Vfr. I must admit I enjoy the I4 more than the V4. I enjoy the smooth low end torque over the jerky jerky V4 and it’s quaint but kinda useless v tech. The vfr left me stranded when the wiring harness around the battery became just a bit to crispy and let go. Also had the ground issue which nearly left me stranded. Honda really needed a better ECU, charging system and a more robust wiring harness before unleashing the thing to the public. The Suzuki has had no weirdness and for me is the more enjoyable of the two. If I sold the Bking for a vfr I would have regretted it.
  18. Yesterday
  19. Gazzaboo
    Would my reading be correct i would mostly be riding twisting and winding A & B roads so leaving it on a 170 tire would be more enjoyable to throw around than fitting the 180 tire
  20. FromMaine
    Ditto. No issues with welding, all manufacturers weld their frames. Its where that matters. Nice work also!
  21. FromMaine
    Started to refinish my new to me 8 spoke. Bought here courtesy of member SamW. Gave it a degrease, couple of good scrubs, scraped and sanded, then an alcohol bath. Dried for a few days then light sand again on bare metal, alcohol and then metal primer. Will let this cure for 3-4 days then sand and apply 2 top coats. These need a week each to cure properly. This process takes a while to get right, but I drank the White Rims Kool-aid a long time ago. 😁 .
  22. Worfje
    Hi, I just ran into this aftermarket replacement flexible PCB of dashboard on eBay for 30 pounds (roughly 34 euro's / 40 dollar, excluding shipping).
  23. bmart
    That's a handsome mousetrap! (I'm in Charlotte, so not too far from you) You seem to like mods, maybe delink the brakes while you're that far into everything. I never noticed any issues with them linked, but the ease of bleeds delinked is appealing. Nice work!
  24. Worfje
    Hi Dutch724, Barbequed mice, nice. Would you have a picture of the cracked frame? I had a look into the COP 'upgrade'. Nice for looks, but no clear performance/reliability improvement found. I installed the AS3 set also and it was pretty straightforward. What issues did you ran into? Extra? There is one vacuum line connected to the flapper valve. Just put a bolt in the disconnected vacuum line. Have a look here on Yup Tub. It is a pita, but as stated it is doable and follow the procedure / order stated in the service manuals and exploit your family to help out. I have delinked the system, since after 26 years I thought it was time to ditch it to guarantee reliability. Personally, besides the improved reliability, I appreciate riding/braking delinked. Nice work!
  25. darthdoud
    Ok thanks for the info and help. The tacho has not worked at all the fuel pump solenoid isn't working as well, I didn't think I'm getting a signal from the sparking unit under the seat
  26. keny
    So Thursday I got a note the camshafts I ordered had arrived but sadly the place where to pick them up had closed early for some reason, so did pick up on Friday on lunch break, they look good as are correct So was time to mount the good lift fingers And out whit the bad 3 To me it looks more they have suffered from dirt falling as valve cover has been taken off than suffer from loss of lubrication. Anyway in goes the good second hand camshaft Then valves adjusted and engine turned over to secure before turning engine by starter motor to see oil comes to camshafts. I did actually take the camshaft holders as the H shaped oil tube from the 88-89 head to be sure no blocking in there. They are parts that are interchangeable aside the lift fingers. So valve cover on, did change the fuel line as old had crack's in the ends to be on safe side, and as I did put in a universal fuel line I did put some zip ties to secure it's not rubbing against carburators, I did also take the long protection plastic of old fuel line and got the new into it. So now just to get fuel and test start and hope the carbs does not flood..... 🤞
  27. keny
    Yesterday I got the things needed to mount the rear wheel on the Zephyr So pin bolts in as sprocket on And then wheel on the bike Looks to be nice in center as chain line good to, it will be closely checked as I mount the chain. 🙂
  28. keny

    Anything goes!

    Images added to a gallery album owned by keny in Member's Gallery

    Other VFR and other pics....
  1. Load more activity

  • Blogs

    1. HispanicSlammer

      A blog by HispanicSlammer in General

      • 122
        entries
      • 565
        comments
      • 302341
        views

      Recent Entries

      HispanicSlammer

      med_gallery_491_3463_298783.jpg

      Juniper Pass

      I took a day off from work and also from my bicycle training to take out the Veefalo one last time before the weather turns ugly, supposed to snow the rest of the week and possibly start sticking to the ground along the Colorado Front Range. I took a leisurely pace up hwy 105 toward Morrison and got reacquainted with the bike since its been over a month since I took any sort of twisties on it at all, hwy 105 is a scenic ride along the front range between Denver and Colorado Springs, its mostly easy fast sweepers and lite traffic so its a favorite road of mine when going north. Then I have to negotiate a bit of traffic near Highlands ranch and up hwy 470 into the mountains. I decided to take the Morrison Exit and try either Lookout Mountain or head up Golden Gate Canyon - this time it was Lookout Mountain, I was sort of making it up on the fly as I went along. Lookout Mountain is my old bicycling haunt from my days while I was working at Coors, its a killer ride and all uphill - I don't think I could do it today If I had to, not quite there yet! I saw a whole bunch of riders doing it though and wished I was in shape enough to be there doing it as well. 30 more lbs and I will be able to do it! On this day I would do it on the Veefalo instead.

       

       

       

       

      I took a video from the gateway to the top at the Lookout Mountain State Park, getting past riders, the guy in the green jacket actually pretty much astounded me with how far he had gotten in the short time it took me to set up my camera, some 3 miles at least and up to the gateway from the turn off at hwy 6! Amazing I thought. I took the first two turns slow then got more comfortable as I went up further, till I was doing well, I made some gearing mistakes and took the tight 15mph marked hairpins in the wrong gear so I lugged it a bit on one or two. Still enjoyed it though and then got off at the top and hiked over a rock outcropping for an overview of the road for the pictures below.

       

       

      gallery_491_3463_225077.jpg

      Lookout Mountain - Golden Colorado

      gallery_491_3463_460686.jpg

      Zoomed in

      gallery_491_3463_96202.jpg

      Lookout Mountain Park top of the mountain

      From there I headed up interstate 70 to Idaho Springs for a beer at the Tommy-knockers brewery, I was the only customer in the joint - slow day for them so they treated me like a king! I got a nice tour of the place sort of impromptu, they made me a nice Pastrami sandwich on rye and with the brown ale it was fantastic. I must say the beer is much better there than in the bottles - its always good at the brewery. I am glad I stopped

      gallery_491_3463_328875.jpg

      Tommy-knockers Brewpub Idaho Springs

      gallery_491_3463_290342.jpg

      Idaho Springs Colorado

      gallery_491_3463_432219.jpg

      Mashtuns and fermenters

      gallery_491_3463_278071.jpg

      Rows of fermenters

      I finished my lunch and since the road to Mount Evans is right there I headed up Squaw pass hoping to get in some nice pictures I wasn't expecting what I found, ICE IN ALL THE SHADY PARTS

      gallery_491_3463_419309.png

      Icy patches on Squaw Pass definitely taking it easy on that road

      There were some section where the ice covered the whole road for 300 yards or so I had to roll through it with my legs out to help keep the bike from sliding and falling over, I took it real slow. A Ford pickup was right behind me so I pulled over to let him pass but the guy was going slower then even I was so I pressed on - in places where I could see I just cut over to the oncoming lane and out of the ice where the sun was shining on the road more, but some places there was not alternative so I just had to go slow, good thing it wasn't slick but rather they tossed some gravel over the worst parts so I had some traction!

      I did stop for pictures in all the best spots

      gallery_491_3463_338944.jpg

      Echo Lake at Mount Evans showing off my new plate

      gallery_491_3463_562075.jpg

      Elephant Butte Park and Denver

      gallery_491_3463_271364.jpg

      Close up

      gallery_491_3463_12419.jpg

      Veefalo on Squaw Pass

      gallery_491_3463_298783.jpg

      Juniper Pass

      gallery_491_3463_291678.jpg

      Juniper Pass

      gallery_491_3463_385846.jpg

      Mount Evans

      My route A is home B is Tommy-knockers

       

    2. MartinkaP's Blog

      A blog by martinkap in General

      • 8
        entries
      • 77
        comments
      • 36859
        views

      Recent Entries

      martinkap
      Latest Entry

      I Am Back !

      gallery_7692_2036_18129.jpg

      Not that it matters and not that I expect anyone had noticed, but to those who sent me "where are you?" I would like to say I am back. Not only that I am officially returning to VFRD after nearly 2 months break but I have also ridden my Hawk last weekend and had FUN! Let me restate that; I had major fun riding! Something I have almost given up on.

      Most of you have been riding your whole adult lives and riding is not only a hobby to you, it is part of you. But I started riding three years ago and even though I have encounter some setbacks, till this spring I loved riding with whole my heart. However, I have always considered riding as my hobby. As a hobby which suppose to make my life better, more fun and more rich. Life is too short to do something which we don't fully love.

      My love of riding received a first major scar this spring: I lost a friend on the racetrack. He was a total stranger who offered me his help after I lowsided at CMP track last year. I still remember hearing his "Hi, my name is Todd, do you need help?" while I was duct-taping my roadrash from ripped jacket. He helped me straighten up the shifter and we kept in touch. The next time we saw each other was the day he died.

      With 9 months delay, I can say that Todd's death shook me more than I have realized. It rooted fear in me which was fueled by seeing and hearing about others getting hurt over and over again. If I was to summarize this year - it would be one big accident report. I became sensitive to every broken bone, every roadrash, every lowside. And even though I did 10 track days this year, I became slower and slower and slower. Suddenly, I have acquired this 'grandma' riding style on the road, frozen with fear that behind every corner there is car standing in my lane, or major sand trap or deer staring at me ... I was crippled with fear not only for me about also for my fellow rider.

      So, at the end of this year, I rode more and more by myself. I could not bear the feelings of responsibility for others on the road and my lines were crippled by my own fears. It all culminated this fall at WDGAH. In a freaky accident Love2rideh82crash was taken down by a truck crossing into our lane. I was done. I finished the weekend, locked the VFR into a garage and took a break.

      Until the last weekend, I pretended that motorcycles do not exists. As a last instance after 2 months break from riding, I decided to go to CMP track to see if I can still have fun. I also felt like I should go for the memory of Todd. I went and I had fun! I had much more fun than I expected and the most fun on track I can remember. Suddenly the whole track connected into an uninterupted line of turns and I felt one with the bike riding around! I was giggling like a little girl in my helmet and keep on giggling ever since smile.gif

      Granted I was not the fastest one and through out the weekend, I have never exceeded about 60% of my riding abilities, but I had no "oh-shit" nor 'blond' moments. I could have maybe go faster, I could have brake later for the turns and I could have lean further, but I am no Rossi nor Stoner. I decided to ride for fun and I had amazing blast riding well within my comfort zone.

      I was proud of myself when, after bandaging Ricks arm, I was able to distance myself and go back to riding without the year-long fear. I did feel bad for him but the feelings were not crippling my lines nor my mind. And when a total stranger came to me and said "Hi, my name is Todd", my heart stopped for a minute though but I suddenly knew that my life went a full circle. I probably will never win MotoGP :idea3: , but I am back! :wheel:

×
×
  • Create New...

Important Information

By using this site, you agree to our Privacy Policy.

  I accept