Member Contributer Duc2V4 Posted February 15, 2014 Member Contributer Share Posted February 15, 2014 I know a few people on the forum had links to places to find/buy well nuts, Lowes Home Improvement Center being one of them. Well stopping by two different Lowes, I could not find the metric versions, then going online they had appeared to not have any in stock, so I went to the internet...Low and behold I found this place http://www.clipsandfasteners.com/Nuts_Well_s/138.htm and was able to find metric well nuts! The best part of it is that they are local, in fact they are literally across the street from where I used to work! Figured I'd share with the class, who knows, maybe someone already posted about this place but figured I share anyway. They sell them in bulk only, but at $14.15 for a box of 25 ($.56 ea.) why not buy them in bulk. Not like I'll never need them again, right? Link to comment Share on other sites More sharing options...
SEBSPEED Posted February 15, 2014 Share Posted February 15, 2014 Nice find. I believe I have a new Honda one at home. I printed out their catalog page with all the dimensions, I will try and verify later today. Link to comment Share on other sites More sharing options...
Member Contributer swfarrar Posted February 15, 2014 Member Contributer Share Posted February 15, 2014 Thanks for the tip and please report back on how well they work. Several years ago I bought some aftermarket well nuts online and while the thread was correct the rubber body was just a tiny bit smaller diameter than the OEM version, making it very difficult to keep them from spinning in the hole when the bolt was turned. Can't remember where I got them, though. Link to comment Share on other sites More sharing options...
Member Contributer Switchblade Posted February 15, 2014 Member Contributer Share Posted February 15, 2014 Looks like Tmac will be the perfect venue to distribute said parts. Thanks Duc ... Link to comment Share on other sites More sharing options...
Member Contributer MadScientist Posted February 15, 2014 Member Contributer Share Posted February 15, 2014 I don't have the box at hand anymore, but I ordered a box from that vendor last spring for a bulk replacement of the dry rotted and permanently squished well-nuts on the bike. The ones I ended up ordering were slightly shorter than the stockers and probably about the original diameter. They were loose enough to fall out if you turned a fairing over but they tightened up just fine - no spinning. I'll see if I can find the email receipt, maybe it has the part number. Found it: https://www.clipsandfasteners.com/ProductDetails.asp?ProductCode=A16242 The other thing I remembered was that I wish the rubber "head" was a little larger diameter. These may be a better fit: http://www.clipsandfasteners.com/Well_Nut_M5_8_665_Length_p/a16248.htm Link to comment Share on other sites More sharing options...
Member Contributer Duc2V4 Posted February 15, 2014 Author Member Contributer Share Posted February 15, 2014 I don't have the box at hand anymore, but I ordered a box from that vendor last spring for a bulk replacement of the dry rotted and permanently squished well-nuts on the bike. The ones I ended up ordering were slightly shorter than the stockers and probably about the original diameter. They were loose enough to fall out if you turned a fairing over but they tightened up just fine - no spinning. I'll see if I can find the email receipt, maybe it has the part number. Found it: https://www.clipsandfasteners.com/ProductDetails.asp?ProductCode=A16242 The other thing I remembered was that I wish the rubber "head" was a little larger diameter. These may be a better fit: http://www.clipsandfasteners.com/Well_Nut_M5_8_665_Length_p/a16248.htm I bought a box of both just for grins, but the 16248 matched what I had used in the past with no issues. I'll probably change one or two on my 09 that are on the cusp of going south. I'll let you all know what the results are.Cheers Link to comment Share on other sites More sharing options...
Member Contributer Switchblade Posted February 15, 2014 Member Contributer Share Posted February 15, 2014 I don't have the box at hand anymore, but I ordered a box from that vendor last spring for a bulk replacement of the dry rotted and permanently squished well-nuts on the bike. The ones I ended up ordering were slightly shorter than the stockers and probably about the original diameter. They were loose enough to fall out if you turned a fairing over but they tightened up just fine - no spinning. I'll see if I can find the email receipt, maybe it has the part number. Found it: https://www.clipsandfasteners.com/ProductDetails.asp?ProductCode=A16242 The other thing I remembered was that I wish the rubber "head" was a little larger diameter. These may be a better fit: http://www.clipsandfasteners.com/Well_Nut_M5_8_665_Length_p/a16248.htm I bought a box of both just for grins, but the 16248 matched what I had used in the past with no issues. I'll probably change one or two on my 09 that are on the cusp of going south. I'll let you all know what the results are.Cheers Thats cheaper for a box then what i paid for 6 from Partszilla. Link to comment Share on other sites More sharing options...
Member Contributer vfr350 Posted February 16, 2014 Member Contributer Share Posted February 16, 2014 Now if i could just find black chrome bolts to replace the stock chrome on the outside of the fairing, I know those rubber deals have to be shot, nice find. Suppose could never find a black replacement for that big flared one though. Anyone ever try to replace the bottom fairing clips/push pins with this sort of setup? Link to comment Share on other sites More sharing options...
wera803 Posted February 16, 2014 Share Posted February 16, 2014 Anyone ever try to replace the bottom fairing clips/push pins with this sort of setup?I put quarter turn fasteners on the 2 bottom fairing connection points instead of the push pins. Link to comment Share on other sites More sharing options...
Member Contributer vfr350 Posted February 16, 2014 Member Contributer Share Posted February 16, 2014 Guess I'll have to check the hardware store on the quarter turns, looking them up has left me a bit confused. Thanks for the suggestion. Link to comment Share on other sites More sharing options...
Member Contributer Duc2V4 Posted February 16, 2014 Author Member Contributer Share Posted February 16, 2014 Guess I'll have to check the hardware store on the quarter turns, looking them up has left me a bit confused. Thanks for the suggestion. Go to http://www.kurveygirl.com/shop/index.php?cPath=104, they carry D-Zus 1/4 turn fasteners. Link to comment Share on other sites More sharing options...
spud786 Posted June 14, 2014 Share Posted June 14, 2014 Yes if anyone comes up with the real thing , speak out, I rather just get the oem if not as good. Link to comment Share on other sites More sharing options...
Member Contributer vfrcapn Posted June 22, 2014 Member Contributer Share Posted June 22, 2014 Guess I'll have to check the hardware store on the quarter turns, looking them up has left me a bit confused. Thanks for the suggestion. Go to http://www.kurveygirl.com/shop/index.php?cPath=104, they carry D-Zus 1/4 turn fasteners. I think that's where I'm going next, just paid $2.65 ea. for OEM this week to fix a few failed ones. Link to comment Share on other sites More sharing options...
LSO Posted March 6, 2015 Share Posted March 6, 2015 I'm looking to change to the 1/4 turn Dzus, will any work? which ones do you recommend? They have a lot of different sizes from what I see. Thanks Link to comment Share on other sites More sharing options...
wera803 Posted March 6, 2015 Share Posted March 6, 2015 I'm looking to change to the 1/4 turn Dzus, will any work? which ones do you recommend? They have a lot of different sizes from what I see. ThanksCheck out Kurvy Girl. She sells them made for OEM plastic. Link to comment Share on other sites More sharing options...
WERA910 Posted March 6, 2015 Share Posted March 6, 2015 Guess I'll have to check the hardware store on the quarter turns, looking them up has left me a bit confused. Thanks for the suggestion. Go to http://www.kurveygirl.com/shop/index.php?cPath=104, they carry D-Zus 1/4 turn fasteners. I think that's where I'm going next, just paid $2.65 ea. for OEM this week to fix a few failed ones. I did the same thing... just added 10 to a Service Honda order last week... gotta remember to search VFRd first! Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.