8200rpm Posted December 28, 2019 Share Posted December 28, 2019 Bought a used 1998 with 33k. I think an aftermarket R/R was installed but not sure which one (resembles a Rick’s) or if the wiring is kosher. Help a rider out? Am I good to go for now, leave good enough alone, or does it need some immediate attention? Thanks for your time! Link to comment Share on other sites More sharing options...
Member Contributer gll429 Posted December 28, 2019 Member Contributer Share Posted December 28, 2019 1st.. is the bike charging properly ? if yes.. leave it alone!! if no.. test it and rule out the stator.. if its bad, replace it. Link to comment Share on other sites More sharing options...
Member Contributer mello dude Posted December 28, 2019 Member Contributer Share Posted December 28, 2019 Looks like a Rick's........that wire install job looks terrible.....redo it before it strands you on the side of the road.... Search for a charging test ...the drill.......and get a data point of the health of the system.. If the RR is fine, continue to use, if not replace with a Shindengen FH020aa. www.roadstercycle.com Link to comment Share on other sites More sharing options...
Member Contributer ducnut Posted December 28, 2019 Member Contributer Share Posted December 28, 2019 That’s a Rick’s. There’s no possible way I’d leave that garbage on there. When it fails, hopefully, you’ll be in your driveway and it doesn’t wreck your stator at the same time. The ‘98 I bought had a brand new Rick’s R/R on it. First things I ordered for the bike were a Roadstercycle SH847 Kit, OEM Honda stator, and voltmeter. Link to comment Share on other sites More sharing options...
Member Contributer mello dude Posted December 28, 2019 Member Contributer Share Posted December 28, 2019 1 hour ago, ducnut said: That’s a Rick’s. There’s no possible way I’d leave that garbage on there. When it fails, hopefully, you’ll be in your driveway and it doesn’t wreck your stator at the same time. The ‘98 I bought had a brand new Rick’s R/R on it. First things I ordered for the bike were a Roadstercycle SH847 Kit, OEM Honda stator, and voltmeter. Agreed, I would never intentionally use a Rick's...... either the FH020AA or SH847 is fine, although the 847 is physically larger and takes a bit of creativity to mount. While I 'm at skip the Vfrness too. Link to comment Share on other sites More sharing options...
Member Contributer ducnut Posted December 28, 2019 Member Contributer Share Posted December 28, 2019 15 minutes ago, mello dude said: Agreed, I would never intentionally use a Rick's...... either the FH020AA or SH847 is fine, although the 847 is physically larger and takes a bit of creativity to mount. While I 'm at skip the Vfrness too. I chose on the bottomside of my undertray. On my SV650S, I mounted it under the seat, in the storage area. Link to comment Share on other sites More sharing options...
Member Contributer mello dude Posted December 28, 2019 Member Contributer Share Posted December 28, 2019 I'm running the FH020aa now, and if it ever wears out, I'll take the time to figure out a clean mount for SH847 on the OEM spot on my 5th gen. Link to comment Share on other sites More sharing options...
JoelF Posted December 29, 2019 Share Posted December 29, 2019 I got a used FZ-09 regulator off ebay, mounted it in the stock spot with I think one new hole drilled. Ebay also has harnesses. It's of the newer design, FH020 or similar. Works great and stays cool so no need to increase airflow over it IMO. Link to comment Share on other sites More sharing options...
Member Contributer KevCarver Posted December 30, 2019 Member Contributer Share Posted December 30, 2019 On 12/28/2019 at 1:39 PM, mello dude said: I'm running the FH020aa now, and if it ever wears out, I'll take the time to figure out a clean mount for SH847 on the OEM spot on my 5th gen. I lost my FH012 in 2017, but that was a used ebay special from an R1. Got an 020 brand new from Roadster to replace it. Link to comment Share on other sites More sharing options...
8200rpm Posted December 30, 2019 Author Share Posted December 30, 2019 On 12/27/2019 at 5:57 PM, mello dude said: Looks like a Rick's........that wire install job looks terrible.....redo it before it strands you on the side of the road.... Search for a charging test ...the drill.......and get a data point of the health of the system.. If the RR is fine, continue to use, if not replace with a Shindengen FH020aa. www.roadstercycle.com Thanks for the “Drill”. I’ll bust out the multimeter next time I’m free to tinker. Spent a couple hours too many in the garage the past couple days doing my brakes. Link to comment Share on other sites More sharing options...
tireguy Posted January 14, 2020 Share Posted January 14, 2020 I installed a Rick's on mine more than 10 years ago and have not had any trouble with it all. Charging voltage goes to 14.4 at 2500rpm and stays there right up to 10,000rpm. I did change the stator at the same time and cleaned up every connection point in the charging system at the same time. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.