KevinWoods Posted April 23, 2019 Share Posted April 23, 2019 I had a heck of a time getting out of my parking garage this morning because the buried sensors can’t see my bike . Where I live has a parking garage and there are 2 gates. For both gates I have an access card that lets me in. The problem is my bike isn’t seen by the sensors. One gate has a call button but the other does not. For the 2nd gate I had to wait and follow someone through. Any tips or tricks? Do the neodymium magnets really help? Link to comment Share on other sites More sharing options...
Member Contributer Mohawk Posted April 23, 2019 Member Contributer Share Posted April 23, 2019 Get over the sensor patch & Rev the engine the magnetic field from the gennie will get seen. Link to comment Share on other sites More sharing options...
KevinWoods Posted April 24, 2019 Author Share Posted April 24, 2019 I did some experimenting today and think I have a solution. If I stop directly on top of the cutout lines and put the side stand down, I was able to get past both gates. I will have to do some more experiments tomorrow. I ordered some neodymium magnets and am going to see if those help. Kevin Link to comment Share on other sites More sharing options...
Member Contributer KevCarver Posted April 24, 2019 Member Contributer Share Posted April 24, 2019 2 hours ago, KevinWoods said: I did some experimenting today and think I have a solution. If I stop directly on top of the cutout lines and put the side stand down, I was able to get past both gates. I will have to do some more experiments tomorrow. I ordered some neodymium magnets and am going to see if those help. Kevin I've heard of that with stop light sensors, center stand is better (if equipped). Presumably more iron. Link to comment Share on other sites More sharing options...
Member Contributer MadScientist Posted April 25, 2019 Member Contributer Share Posted April 25, 2019 I've also heard of people mounting a magnet into the heel of riding boots for this reason. Sounds like an idea for a product right there, maybe a velcro-on magnet strap. Would have to find a way to do it without interfering with the grip of the footwear on the pegs or ground though. This is hearsay, of course. I don't know if even a small, high powered magnet is capable of tripping the sensor loops. Link to comment Share on other sites More sharing options...
Member Contributer MooseMoose Posted April 25, 2019 Member Contributer Share Posted April 25, 2019 Pegs are aluminum. Non ferrous. Link to comment Share on other sites More sharing options...
Member Contributer MBrane Posted April 25, 2019 Member Contributer Share Posted April 25, 2019 Loops are inductive not magnetic. It doesn't matter what type of metal it just has to be close enough to disturb the field. Metal toe sliders come in handy for this because you can set 'em right on the loop. Link to comment Share on other sites More sharing options...
Member Contributer Mohawk Posted April 25, 2019 Member Contributer Share Posted April 25, 2019 I just remembered that one place I worked the sensor loops were awkward, if you approached head on it would not open, but if you arrived at one side of the lane & crossed the sensor patch at 45 degrees whilst crossing to the other side of the lane it worked a treat. You could then aim at the opening end of the barrier & get out earlier ! Link to comment Share on other sites More sharing options...
KevinWoods Posted April 27, 2019 Author Share Posted April 27, 2019 I had good results this morning stopping right on the cut out line. I didn’t need to put the side stand down. Great news, one less roadblock to my daily bike commuting! Link to comment Share on other sites More sharing options...
fatshoutybloke Posted April 29, 2019 Share Posted April 29, 2019 I used to have a similar problem in the car park at my previous job if I didn't stop with my engine over the sensor. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.