thewedge Posted January 2, 2018 Share Posted January 2, 2018 First, I have been searching and reading extensively on this. if I missed the information somewhere, I apologize. in short, I would like to remove the convoluted California Emission stuff from my 1996 VFR750. At the same time, I'd like to remove the PAIR valve stuff as well. From my reading: 1. I understand the concepts and am mechanically capable. 2. I could not find an Emissions Delete thread that looked like the stuff on my bike...none seemed to be for a 4th generation. I have attached some pics from the Clymer manual... Can anyone give me the instructions on what needs to be pulled/plugged (using these pictures for reference) to delete the Cal Emission and the PAIR valve from this bike? Again...thank you for revisiting this topic and my apologies again if I missed this in my searches. Link to comment Share on other sites More sharing options...
Member Contributer Lannyl81 Posted January 3, 2018 Member Contributer Share Posted January 3, 2018 Not able to help with the EVAP stuff, but the PAIR removal does require block-off plates put on. These go where the chrome tubes are, above the four exhaust ports. Also need to cap off the tubes in the air filter housing. I removed the PAIR stuff from my '97 just last summer. The front cylinders are easy, the rear not so much. I had to remove the complete exhaust system in order to get the block-off plates on the rears. And the center stand does not need to be removed to get the exhaust system off. Good luck, will take a couple of hours. Link to comment Share on other sites More sharing options...
thewedge Posted January 3, 2018 Author Share Posted January 3, 2018 Anybody know if the VFR800 PAIR Valve Block off plates will fit the 4th gen 750? or am I stuck manufacturing my own? Link to comment Share on other sites More sharing options...
Member Contributer Burns Posted January 3, 2018 Member Contributer Share Posted January 3, 2018 55 minutes ago, thewedge said: Anybody know if the VFR800 PAIR Valve Block off plates will fit the 4th gen 750? or am I stuck manufacturing my own? they are much different. Link to comment Share on other sites More sharing options...
Member Contributer Burns Posted January 3, 2018 Member Contributer Share Posted January 3, 2018 been a while since I did this on the 4th gen.. you shouldn't have an evap can (unless yours is somehow a CA bike) so that should make it a little easier.. I think i had just made block off plates (4 - one for each cyl) using some heavy steel plate - easy enough.. just get some rubber vacuum caps from auto store to cap anything that goes to the carbs (might be a plug on airbox that might need plugged also).. should be one line for each of the two valves going to the carb banks... someone please correct me if I'm wrong.. been years since I did this.. lol Link to comment Share on other sites More sharing options...
Member Contributer Burns Posted January 3, 2018 Member Contributer Share Posted January 3, 2018 https://www.ebay.com/itm/Honda-VFR-750-VFR750-Interceptor-Exhaust-Emissions-Plate-AIS-Smog-Block-Off-Kit-/232139921877 Link to comment Share on other sites More sharing options...
thewedge Posted January 3, 2018 Author Share Posted January 3, 2018 Awesome...thanks. Bought the kit...I've made some detailed diagrams for the EVAP and the PAIR and think I have it covered. The 4th gen is very different than the earlier ones of the 800's so it took some study to get it straight. Mine is a California bike (no idea how it go here in VA). Link to comment Share on other sites More sharing options...
Member Contributer JZH Posted January 4, 2018 Member Contributer Share Posted January 4, 2018 22 hours ago, Burns said: been a while since I did this on the 4th gen.. you shouldn't have an evap can (unless yours is somehow a CA bike) so that should make it a little easier.. I think i had just made block off plates (4 - one for each cyl) using some heavy steel plate - easy enough.. just get some rubber vacuum caps from auto store to cap anything that goes to the carbs (might be a plug on airbox that might need plugged also).. should be one line for each of the two valves going to the carb banks... someone please correct me if I'm wrong.. been years since I did this.. lol FWIW, this is exactly what you do on a 3rd gen CA-spec VFR. I usually say to cap everything except the large, angled vent port between the two rear carbs (see below). I prefer the vinyl vacuum caps--rubber deteriorates. Ciao, Link to comment Share on other sites More sharing options...
SEBSPEED Posted January 4, 2018 Share Posted January 4, 2018 FYI for anyone else, the Hayabusa exhaust port block offs work perfectly on the 4th gen. Just another shopping option. Link to comment Share on other sites More sharing options...
squirrelman Posted January 8, 2018 Share Posted January 8, 2018 there is another option besides block-off plates: Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.