Member Contributer Dutchy Posted October 22, 2019 Author Member Contributer Share Posted October 22, 2019 Well, the Gilera dit not start "off the bat", so I will need to dig deeper. Carb was cleaned ultra-sonically, I have spark I have compression (I think...) I hove no kickstarter so pushing it is.... To no avail. so I gave up for the day, took the exhaust off and drove home Strarted cleaning which include putting a powerdrill+wire wheel on her... Then, when I helt it vertically, a shitload of primarily sand streamed out With rust flakes in for good measure. Ir was quite a volumen/weight So I'm (hoping) that this somehow blocked the exhaust flow so much that it hampered attempts to start her. Back on it maybe Thursday or Friday..... 🍀🍀🍀 Quote Link to comment Share on other sites More sharing options...
jeremyr62 Posted October 22, 2019 Share Posted October 22, 2019 Take the spark plug out and put your finger down the hole (not that hole). Now push it down the road and test for compression. with your finger. And try not to get arrested at the same time. I take it you have plenty of petrol? Quote Link to comment Share on other sites More sharing options...
jeremyr62 Posted October 22, 2019 Share Posted October 22, 2019 The density of iron corrosion products is a lot less than the iron itself so hopefully you still have some steel left. Quote Link to comment Share on other sites More sharing options...
Member Contributer Dutchy Posted October 23, 2019 Author Member Contributer Share Posted October 23, 2019 9 hours ago, jeremyr62 said: Take the spark plug out and put your finger down the hole (not that hole). Now push it down the road and test for compression. with your finger. And try not to get arrested at the same time. I take it you have plenty of petrol? There is plenty compresseion methink. With the sparkplug revmoved and gearbox in 1st, rotatin the rear wheel is fairly easy. I can hear the piston puffing. with the spark plug is, it reauires siginificant effect. Och well, will try again in a couple of days. Quote Link to comment Share on other sites More sharing options...
jeremyr62 Posted October 23, 2019 Share Posted October 23, 2019 And the timing is OK? If you have spark, petrol and compression it will fire eventually. Quote Link to comment Share on other sites More sharing options...
Member Contributer Dutchy Posted October 24, 2019 Author Member Contributer Share Posted October 24, 2019 Rocker cover gasket is iffy I reckon. Lifted the cover and found fresh oil on tge face and gasket. So I cut a new one.. will try tomorrow if this proves to be "it"... Never done one before, never too old to learn. Quote Link to comment Share on other sites More sharing options...
Member Contributer Dutchy Posted October 27, 2019 Author Member Contributer Share Posted October 27, 2019 And so the farkling begins... (Mind you, this is the OEM part the bike came with in 1955. So does this classify as "farkling"?) Quote Link to comment Share on other sites More sharing options...
Member Contributer Dutchy Posted October 29, 2019 Author Member Contributer Share Posted October 29, 2019 "Esther" lives!!! VID-20191029-WA0040.mp4 1 Quote Link to comment Share on other sites More sharing options...
jeremyr62 Posted October 29, 2019 Share Posted October 29, 2019 Sounds like a two stroke. Your neighbours will so happy to hear that first thing in the morning. Quote Link to comment Share on other sites More sharing options...
Member Contributer Dutchy Posted October 31, 2019 Author Member Contributer Share Posted October 31, 2019 "I love the smell sound of 1950's 4-stroke in the morning; it sound like........ VICTORY!!!" 1 Quote Link to comment Share on other sites More sharing options...
Member Contributer Dutchy Posted October 31, 2019 Author Member Contributer Share Posted October 31, 2019 The Gilera had (according to the Italian bike tech guru that made her run) a wrong sparkplug and a 2-stroke carb with incorrect jetting, connecting tube to a head a Walmart bit of cobbled together tubing. so he turned a new one. We tried salvaging as much parts from the incorrect carb to rebuild a proper one with a MA 18 B shell. But after fiddling with jets, needle height and shape, trying to ensure proper fuel level inside the bowl, he just said "who cares" and removed a perfect one from (one of) his MV Agusta's for me.... He owns a few yes, And knows how to turn from solid aluminium bar ... Han the THE MAN!!! 1 Quote Link to comment Share on other sites More sharing options...
Member Contributer Dutchy Posted October 31, 2019 Author Member Contributer Share Posted October 31, 2019 The jury is still deliberating.... Quote Link to comment Share on other sites More sharing options...
Member Contributer Captain 80s Posted October 31, 2019 Member Contributer Share Posted October 31, 2019 I did the left one with some headlight film as a nod to an endurance racer. Right now it is just the right that operates on low beam, 2 Quote Link to comment Share on other sites More sharing options...
Member Contributer Dutchy Posted October 31, 2019 Author Member Contributer Share Posted October 31, 2019 I might go the yellow film route at some point..... Quote Link to comment Share on other sites More sharing options...
jeremyr62 Posted October 31, 2019 Share Posted October 31, 2019 Tacky 😁 Quote Link to comment Share on other sites More sharing options...
Member Contributer Dutchy Posted November 1, 2019 Author Member Contributer Share Posted November 1, 2019 The engine with the matching #'s to the frame has some "experience"... Quote Link to comment Share on other sites More sharing options...
Member Contributer Dutchy Posted November 2, 2019 Author Member Contributer Share Posted November 2, 2019 Perhaps this rendering will look better.... 2 Quote Link to comment Share on other sites More sharing options...
keny Posted November 6, 2019 Share Posted November 6, 2019 On 10/31/2019 at 8:51 PM, Captain 80s said: I think that RC24 (26?) looks so stunning! 1 Quote Link to comment Share on other sites More sharing options...
Member Contributer Dutchy Posted November 8, 2019 Author Member Contributer Share Posted November 8, 2019 Lovely day for it "Don't pay the ferryman" (cos it is free...) Some of them are out of season.... Had a look at an AGV Legend, but the L too tight and XL too loose.... (I have an ARAI head... 😪) 1 Quote Link to comment Share on other sites More sharing options...
Member Contributer Captain 80s Posted November 8, 2019 Member Contributer Share Posted November 8, 2019 Quote Link to comment Share on other sites More sharing options...
Member Contributer Dutchy Posted November 8, 2019 Author Member Contributer Share Posted November 8, 2019 Oh wow!! Quote Link to comment Share on other sites More sharing options...
Member Contributer Dutchy Posted November 8, 2019 Author Member Contributer Share Posted November 8, 2019 Mind you, Ago raced on Aermacchi, not Gilera... Maybe I should look for a Simoncelli lid.... 😎 1 Quote Link to comment Share on other sites More sharing options...
Member Contributer Dutchy Posted November 15, 2019 Author Member Contributer Share Posted November 15, 2019 Donor engine, really clarty... Time for some therapy (or penance? Fricking cold outside) Ah! There IS a # underneath 65 years of grime... That makes this a 150cc Sport 1st gen 😎 Easy with the right tool Store for later I give up for today, too bloody cold 😪 Quote Link to comment Share on other sites More sharing options...
Member Contributer Dutchy Posted November 15, 2019 Author Member Contributer Share Posted November 15, 2019 Ok, one more... Quote Link to comment Share on other sites More sharing options...
Member Contributer Dutchy Posted November 16, 2019 Author Member Contributer Share Posted November 16, 2019 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.