NRSPTR Posted July 24, 2013 Share Posted July 24, 2013 When I installed my Leo's this spring, I wanted as much of that sweet V4 sound as I could get. Needless to say, both the baffles and the discs with the 5 holes stayed sealed in their respective bags. While I love the low bubbly grumble that open pipes provide, the deceleration popping has always been a little tiresome on longer rides. After recently installing a power commander, I was noticing the popping becoming more prevalent. On a whim, I decided to pull the cans off and install the 5 hole discs just to see what effect they might have. Wow, I am loving this decision! Decel popping is almost non existent now. The overall sound level is ever so slightly reduced, but not noticeably so, unless you're looking for it. I am also noticing slightly crisper throttle response. As for the purpose of these discs, I've heard some people say it's to provide backpressure, and some say that its just another DB killer. Not being a mechanic, I won't even attempt to dissect the benefit or degradation of performance through the installation of these, but I am extremely happy with how the bike is running and sounding with them installed. My only complaint is that the discs do rattle some at low temp idling. I thought about applying a thin bead of RVT to the recess where they sit, but thought I'd see if anyone else had any other ideas to secure them. Link to comment Share on other sites More sharing options...
Member Contributer Rice Posted July 24, 2013 Member Contributer Share Posted July 24, 2013 Instead of cilicone, I would apply exhaust sealer paste. It won't burn off, like the cilicone might. Don't have the LV myself, so take my advice with a grain of salt. Link to comment Share on other sites More sharing options...
NRSPTR Posted July 24, 2013 Author Share Posted July 24, 2013 Thanks Rice, would this paste adhere to the disc? Link to comment Share on other sites More sharing options...
Member Contributer luvtoleanit Posted July 24, 2013 Member Contributer Share Posted July 24, 2013 The popping is caused by your PAIR system. Remove it and block it off and the problem will go away. Link to comment Share on other sites More sharing options...
Member Contributer Rice Posted July 24, 2013 Member Contributer Share Posted July 24, 2013 Paste sets as a more or less permanent solution. In your case I'd use a few drops around the perimeter of the disc just enough to stop the vibration. It is possible to remove it later, but you don't need a lot of it here, so use as little as possible. Link to comment Share on other sites More sharing options...
NRSPTR Posted July 24, 2013 Author Share Posted July 24, 2013 Luvtoleanit, pairs are already blocked. Thanks Rice, I'll give this a try! Link to comment Share on other sites More sharing options...
Member Contributer luvtoleanit Posted July 24, 2013 Member Contributer Share Posted July 24, 2013 Interesting and never seen that before then, my apologies, and good luck! Link to comment Share on other sites More sharing options...
NRSPTR Posted July 24, 2013 Author Share Posted July 24, 2013 luvtoleanit, No apology necessary, thanks for the input! Link to comment Share on other sites More sharing options...
Member Contributer HighSideNZ Posted July 26, 2013 Member Contributer Share Posted July 26, 2013 Hi I have the LV cans on my 2010 with pair valves removed and PCV fitted. I've not installed the discs or baffles in the cans and have never had the decel popping since putting the PCV on and getting rid of the pair valves. Just me 2 cents worth. Cheers Phil Link to comment Share on other sites More sharing options...
enzed_viffer Posted July 26, 2013 Share Posted July 26, 2013 Instead of cilicone, I would apply exhaust sealer paste. It won't burn off, like the cilicone might. Don't have the LV myself, so take my advice with a grain of salt. I had baffles made up for my VTR1000 that a previous owner had bored the muffler cores out of. The whole time I owned the bike they were held in only by high-temperature black silicone. Not only did it seal the gap between the baffles and the muffler bodies, but being flexible it didn't crack or work loose. Link to comment Share on other sites More sharing options...
Member Contributer The mailman Posted July 26, 2013 Member Contributer Share Posted July 26, 2013 I put the discs in just for the hell of it and had two people on separate occassions tell me that my VFR sounded like a VW. THEY CAME OUT IMMEDIATELY! I didn't care for the rattling that you mentioned either. No discs or tubular baffles for me. Even running like this, my girls have told me that this is much quieter than the D&D on my '97. The LV is a happy medium for me between stock and D&Ds. Link to comment Share on other sites More sharing options...
NRSPTR Posted August 2, 2013 Author Share Posted August 2, 2013 I put the discs in just for the hell of it and had two people on separate occassions tell me that my VFR sounded like a VW. A VW, really, can't say that I've ever heard a VW that sounds like this... leos.mov Ended up using RVT, since I already had some, to secure the disc's and stop the rattle, so far so good. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.