Guest Ahmageddon Posted March 6, 2012 Share Posted March 6, 2012 Installed Helibars last week and I noticed when I took apart the throttle housing that one of the throttle cables was down to a single strand, with the rest frayed off and bent backwards. I have never replaced throttle cables and could not find anything in the manual, is this a simple fix? Also, any suggestions on where to buy/which cables to purchase whether OEM or an alternate brand so this doesn't happen again? Link to comment Share on other sites More sharing options...
Veefer800Canuck Posted March 6, 2012 Share Posted March 6, 2012 It's fairly simple, you'll have to prop up the tank and remove the old cable, route the new one the same way. Was your old cable kinked or misrouted? what about the guide where it comes into the switchgear, was that dislodged or something? My throttle cables are 13 years old and look great, so I suspect something is up with yours. After install, run the bike in neutral and move the bars from side to side fully to be sure the revs do not increase, otherwise you'll be in for a surprise in low speed turns. The manual has diagrams for correct cable routing. Link to comment Share on other sites More sharing options...
Guest Posted March 6, 2012 Share Posted March 6, 2012 Yeah, I am not sure how so much damage could have been caused to the cable itself. The cable itself did not appear kinked and was routed as shown in the diagrams. I will have to check the guide when I get a chance to look at the bike again. Will the special extension tool be needed to prop the tank up as you say? Link to comment Share on other sites More sharing options...
Veefer800Canuck Posted March 6, 2012 Share Posted March 6, 2012 You can use a wooden dowel, or a hammer, just about anything the right length. Just be sure it's secure And don't bump it! Link to comment Share on other sites More sharing options...
Member Contributer AnikMankar Posted March 7, 2012 Member Contributer Share Posted March 7, 2012 After installing helibar - i have installed the ST1100 cables they are a great fit and the correct length (longer)...Helibar mentions to pass the cables from the front of the fork / meters and then slide it from the left down to the throttle body. The problem is with that the cables hit the meters(top cowl) and restricts handling. I have passed it under the fork and yoke. Link to comment Share on other sites More sharing options...
Guest Posted March 7, 2012 Share Posted March 7, 2012 After installing helibar - i have installed the ST1100 cables they are a great fit and the correct length (longer)...Helibar mentions to pass the cables from the front of the fork / meters and then slide it from the left down to the throttle body. The problem is with that the cables hit the meters(top cowl) and restricts handling. I have passed it under the fork and yoke. Thanks for the advice. Do you recall where you purchased the ST1100 throttle cables from? Link to comment Share on other sites More sharing options...
Member Contributer AnikMankar Posted March 7, 2012 Member Contributer Share Posted March 7, 2012 Speedsupplies...they are a little cheaper than bikebandit even after discounts Link to comment Share on other sites More sharing options...
Member Contributer RedShed Posted March 8, 2012 Member Contributer Share Posted March 8, 2012 Speedsupplies...they are a little cheaper than bikebandit even after discounts Are these the right part numbers for the longer cables? 17910-MT3-000 cable A and 17920-MT3-000 cable B Link to comment Share on other sites More sharing options...
Member Contributer AnikMankar Posted March 8, 2012 Member Contributer Share Posted March 8, 2012 those part numbers are correct. Link to comment Share on other sites More sharing options...
Member Contributer maxredline Posted March 14, 2012 Member Contributer Share Posted March 14, 2012 Question, how much longer are the ST cables? Link to comment Share on other sites More sharing options...
Member Contributer AnikMankar Posted March 14, 2012 Member Contributer Share Posted March 14, 2012 i think abt 3 to 4 inches Link to comment Share on other sites More sharing options...
Member Contributer RedShed Posted March 14, 2012 Member Contributer Share Posted March 14, 2012 Question, how much longer are the ST cables? I'd be happy to measure them for you when they arrive, but the "B" cable is on backorder from honda. ETA is 4/2 Link to comment Share on other sites More sharing options...
Member Contributer AnikMankar Posted March 14, 2012 Member Contributer Share Posted March 14, 2012 http://imageshack.us/photo/my-images/15/img5551jf.jpg Link to comment Share on other sites More sharing options...
Member Contributer maxredline Posted March 14, 2012 Member Contributer Share Posted March 14, 2012 If someone could measure them that would be fantastic! Link to comment Share on other sites More sharing options...
Member Contributer CasualSwede Posted March 16, 2012 Member Contributer Share Posted March 16, 2012 My eyecrometer says they're about two inches longer. Link to comment Share on other sites More sharing options...
Guest Posted March 24, 2012 Share Posted March 24, 2012 Just got my ST1100 cables in...I would measure but I have no measuring tape/stick/anything (sad, I know). Just curious, both the cables look identical to me. Does it matter which one is installed where? If so could someone point out the difference in the two cables. This whole push/pull seems misleading since both pull... Link to comment Share on other sites More sharing options...
Member Contributer AnikMankar Posted March 25, 2012 Member Contributer Share Posted March 25, 2012 one with 2 nuts at the body end is the pull... Link to comment Share on other sites More sharing options...
Guest Posted March 25, 2012 Share Posted March 25, 2012 This is exactly what I need to know as I just ordered the Spiegler risers and bar set. I will now order the ST throttle cables now that I have the part numbers. Thanks for putting them up here. Link to comment Share on other sites More sharing options...
NakedViffer Posted March 25, 2012 Share Posted March 25, 2012 And make sure to look at the manuals routing for the cable too, because a lot of the time when people take them off or replace them they fail to use the OE routing and just put it how they think it fits best and end up with problems because of it. And I've worked in repair shops with mechanics who are guilty of this too. Link to comment Share on other sites More sharing options...
Guest Posted March 25, 2012 Share Posted March 25, 2012 If possible I am thinking of just connecting the ends of the new and old cables and use them to pull the new ones through. We will have to see how it goes. I have not had the fairings off yet so I dont know what to expect. The VFR has a little less room than my V-Strom so I expect there to be some swear words flying around. Link to comment Share on other sites More sharing options...
Guest Posted March 25, 2012 Share Posted March 25, 2012 Sorry, I dont mean to make this thread about me. Link to comment Share on other sites More sharing options...
Member Contributer AnikMankar Posted March 26, 2012 Member Contributer Share Posted March 26, 2012 Ruoting I kept same...but at the handle bar side I routed it between the fork and tank. If you pass it from the front I.e. Between fork and meters , they keep getting hit or pinched. Also make sure the brake and clutch lines are made loose and tilted slightly. The master cylinder tabs need to be cutoff. Link to comment Share on other sites More sharing options...
Member Contributer maxredline Posted March 26, 2012 Member Contributer Share Posted March 26, 2012 This is exactly what I need to know as I just ordered the Spiegler risers and bar set. I will now order the ST throttle cables now that I have the part numbers. Thanks for putting them up here. Please take the time to measure them and post up before the install :logo: Link to comment Share on other sites More sharing options...
Guest Posted March 26, 2012 Share Posted March 26, 2012 I will measure the cables and take pictures as I go of the install. Link to comment Share on other sites More sharing options...
Member Contributer VFRMAN Posted December 10, 2015 Member Contributer Share Posted December 10, 2015 digging up an old thread, is it the St1100 or St1300 throttle cables that fit a 5th gen? thanks. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.