Jump to content

PLCGuy

Member Contributer
  • Posts

    85
  • Joined

  • Last visited

About PLCGuy

  • Birthday 09/29/1960

Profile Information

  • Location
    Syracuse, NY
  • In My Garage:
    2001 VFR800
    2010 VFR1200F
    1983 V65 Magna
    2011 Ninja 1000

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

PLCGuy's Achievements

Enthusiast

Enthusiast (6/14)

  • Dedicated Rare
  • Reacting Well Rare
  • First Post
  • Collaborator
  • Conversation Starter

Recent Badges

4

Reputation

  1. Hi PLCGuy, Thank you for your donation of 25.00 USD. We look forward to improving the forums with your donation. Thanks VFRDiscussion
  2. Can any one measure the bezel opening for me, please.... No disassembly required, just fairly accurate numbers on the width of the Dash (which should be the same as the opening in the bezel) thank you
  3. no, no spacers involved, I have the dash and bezel in my hand. I would think the bezel should slide over the dash area
  4. 2001 Dash Bezel Fitment I have a 2001 that the dash Bezel does not seem to Fit around the raised area on the dash. Looking at all the Pics I can, it does appear it should be tight against the back of the dash (see example pic) I have two bezels (one an aftermarket) and both will not lay flat around the raised area. I'm guessing the factory one shrank with UV and the other is well, an import. Can anyone measure the dash raised area for me so I can determine if its my dash or my bezel , please? neither is cheap or easy to get, so I want to get this right. I'm tired of my dash looking like it was in a wreck. thank you!
  5. they are absolutely different, I just did this conversion and was surprised the down pipes were bigger, fortunately my header came with them FYI the down tube gaskets are different too
  6. Says it All. WTB 5th gen fuel tank undented everyone I look at has a crease pm or email me if you have an undamaged one, you'd part with color is irrelevant, it will be painted
  7. perfect! couldn't ask for more
  8. Just trying to "start" at factory
  9. looking for a good side picture and or angle and measurements for this bracket. Mine was bent big time on both sides and the actual angle eludes me, so far. 64511-MBG-D10
  10. sent a msg
  11. And fyi, the wife was fine on the 07 vfr
  12. I have a 2010 vfr1200 with a Corbin lady gunfighter. Great seat, clearly great quality. Unfortunately, it is too long for me, putting my crotch high and against the tank, 4" from the butt pocket. Even more important is my wife hates the seat and says the bike is a no-go for her unless we do something else. My goal was to have a faster vfr and replace my st1100 wth this. So, anyone have an original seat for sale? I want to start there and if that flies, send mine to. Corbin for serious rework
  13. Use a shielded cable and ground the shield. Add a choke in series with the power. Add a filter cap across the power leads.
  14. I purchased ones like these EBay #280568791728 the mechanical quality is good. the finish is good, but uneven. One lever is deep black, one is washed black, as if it should have been in the coating tank a little longer. I emailed them and there is another lever on the way. We'll see when I receive it, but for the price I wasn't unhappy and bought a 2nd set as a xmas present for a friend. Since they are chinese, I'd buy 2 sets for this price and have spares for down the road. FYI, the levers interchange, only the adjusters are handed
  15. Unfortunately, I have to pass. On the road today, won't get back till late, Family Sunday, On the road Monday. Too damn tight!
×
×
  • Create New...

Important Information

By using this site, you agree to our Privacy Policy.