-
Featured Gallery Photo
D200-F25216e
I'd bought this VFR less than an hour before and only had enough time to grab a few photos. This was June 6, 2011 and the VFR was n.o.s. with less than 100 km.Copyright
© Lorne Black
All Activity
- Past hour
-
Ok, so it is beginning to look like condensation rather than anything more concerning at this point. As Captain 80s says, a couple of decent rides, 45 mins to 1 hour, and check how things look. Your report on idle sounds about right. You will know from your previous VFR that honda made them idle high to properly warm up before settling down. If the bike has been sat idle for a time some action will sort me any minor issues out. Let us know how you get on.
-
I treasure mine! Like many on the list, there's still nothing to replace it with that is better. Certainly not $10k better! 🙂
-
Rolling from Goodwill on Bost Rd. in Morganton by 10. Nice easy day. Anyone?
- Today
-
For most 6th gen VFR800s, you can check if your motorcycle has ABS by looking at the color of your brake calipers. If they are gold, your bike has ABS; if they are black, it does not. This is a good initial indicator, but it's always best to consult your owner's manual or contact your local dealership to confirm for your specific model year.
-
The idle is pretty steady at 1200rpm once warmed up which I'd estimate takes around 4 minutes. On the previous photo it does look like the oil level viewing glass has been spray painted and poorly masked off, however this was just road dirt that I hadn't cleaned. I attach a photo of the oil level from this evening, a day later, cold engine, looks healthier than the previous photo from when the bike was running. Coolant level on the tank on the left hand side is in the middle of the min and max markings. I've refitted the fairings now so if the weather holds out I'll take the bike out for a good ride this weekend and report back 🤞
-
hhhhhh joined the community -
I get it, but it was always a reasonable start. I've bought and sold dozens of bikes over the years. Certain bikes are just desirable. 10 year old Busa's are selling for a few grand less than they were new. And try to find one that hasn't been molested. On the other hand, you can pick up a bone stock mint 10 year old VFR for less then half of what they were new. Believe me, I understand. Our bikes weren't that popular. But some of us are enthusiasts, and know exactly what a VFR is..(was). This is my 4th one. Just asking opinions, that's all.
-
Could I have some advice. I have a 2002 Honda vfr800 vtech when I start it’s rough and when throttle applied it wants to die. After 30 seconds it jumps up to 2000rpm and throttle is fine. No issues after that I can turn it off and back on and there is no problem.Any advice or help would be helpful?
-
Shanewalker123 joined the community -
shootfast joined the community -
Hello all!!! I have a small problem that I would like to share to see if I can find a solution. I have a Honda VFR 750 F from 1995. For some time now, when I engage the gears, it does not develop speed the way it did, it takes longer, giving the impression that it is limited. The sound of acceleration doesn't seem to be the same anymore In addition to this, there is one full of gasoline that wasn't there. I changed the air filter and the gasoline filter, but the problem remains. what could it be? What can I check to resolve the problem? Thanks for the help
-
Bombax joined the community -
What he said. I don't precisely understand your note. Pricing is determined by market, not a book or online pricing site. None of those have been even close in a decade or two.
-
Shit loads to anyone who knows their motorcycles
-
I'm thinking about selling my bike. As with any bike, I always check around to see what they're going for and price accordingly. Can someone explain to me the wild pricing I'm observing with these things? I see nice examples anywhere from $3500-$5500! The only online used pricing guide I can find for our bikes is JD Power. They say a excellent 2000 goes for @ $6900! WTF? I know it's not worth that, but then I think to myself... What new bike are you gonna buy that's even close to our beloved 5th gens for less than $10k? Now, my bike certainly isn't new, but it's as close as your gonna get. Anyway, what do you guys think a damn near showroom condition 2000 with 7000 miles is worth? Thanks a bunch
-
Yes, and... After changing the oil, you need to RIDE for a good 45 minutes at full operating temperature to remove any moisture from the crankcases (provided you do not have any issues). Running a bike in the driveway, even until the fans come on, typically introduces moisture. That's why short trips on vehicles is so bad for them and their exhaust systems.
-
Hmm, other opinions needed Tom. Looking at that photo: a. The oil level is just above minimum and a water oil emulsion makes up the rest to the full mark. In cars that would probably indicate a break in the head gasket - not sure about a VFR. Or b. The oil level is higher but the sight glass itself is discoloured and there's a bit of condensation which would not be unusual for a bike that's been sitting over winter. It also looks as though the crankcase has been repainted judging by the poor masking on the sight glass. I think if it was my bike, I would check the coolant level and condition ( hopefully no emulsion in the reservoir), do an oil change and then monitor both over several rides. If the coolant level changes and the oil ends up emulsified then you know you've got a gasket or seal that's failed. Others may have better ideas. Incidentally, on the starting and idle issue you didn't say what rpm the warm idle settled at. For an 8 Gen it should be around 1250 - 1300 iirc. I suspect it's the same for yours
-
The issue of the centre piston on the rear caliper not relieving is now resolved. This would only happen when actuating from the rear brake (that cylinder feeds the rears outer two pistons directly, and feeds centre piston via the front second master cylinder, though the green check and relief valve you see above. I think what was happening is fluid was entering the system through the ball check valve, but could not escape though the tiny relief hole which had blocked after been stood 12 years. The brake initially stuck after cleaning it out as above, it wasn't jammed on, but it wasnt right which was very worrying, I again began the process of confirming and chasing the pressure lock from the caliper back towards the front second master cylinder, but after confirming the pressure released at the rear middle piston banjo, subsequently releasing the rear wheel, I moved on to the PCV under the back right of the fuel tank, only to find I couldn't get it to lock again!? Maybe I just had an air bubble right at the back of the system and I let it out? I did a quick manual bleed over all the points, pumping the front second cylinder by hand, no vacuum/power or check valve hoses, just an 8/10mm spanner and a bit of pipe on all the points, my favourite method to be honest! - The levers are nice and firm now, and after a good blast out, the front brakes are really keen even with light pressure, the back when actuated from the rear still drags for 1/2 second or so but its getting quicker and smoother at releasing, I dont notice it when pulling up at lights any more, the bike free wheels forward back when rocked. Happy, just been out for an hour, great bike, good find. -
Errrrr......thanks. Everyone is entitled to their opinion and I'm not going to challenge yours 😆
-
andrea66 joined the community -
Just so you know, the two posts above are from two of the more knowledgeable members of the forum. Welcome to VFRD.
-
Some good voltage checks especially around the ESR, voltage on fuse test points Ignition On and Off, visual inspections for strange wiring, continuity check of Ignition Switch function. Are all good starting points. Download the Service Manual form the forum if you don't have it. May the Force be With You....There's plenty of info to get the ball rolling, very interested in what you may discover, post photos. Strangest VFR fault I've ever heard of!
-
Previous owner left everything to dealers, I showed him some faults he was not aware of when viewing the bike so not much there Will remove the fairings this weekend and start measuring and tracing and checking for cables that aren't part of the loom. Will make some notes as I go as this will be my first time chasing a electrical issue and that wiring map is already making my eyes hurt
-
Ok, so the red and blue circled areas have been cleaned up with wd40 and a toothbrush. As both areas do move at the same time when you extend the wax unit. Even with wd40 on the shafts and moving parts they still make a squeaking noise when moving them with my fingers. I refitted the airbox etc and started up, the engine sat at 1k revs for around 10 seconds before going up to 2k revs so this is an improvement and an acceptable amount of time for the wax unit to react? Onto my next concern, the oil in the viewing window. After running the bike up to 105 and the fans coming on, the attached photo is how the oil looks, there's a white layer on top of the brown oil at the bottom. According to the service receipts, this oil and filter was changed 9 months, 3000 miles ago. Does this white layer on top of the oil point to there being a broken water pump seal or something or should I get the bike out for a proper ride and see how the oil is afterwards once it's all been mixed and thru the filter properly?
-
6th gen is a little beyond my time, but what is it you want to know? For individual parts you can check the bike-parts.fr website, which has microfiche for both versions. In the old days, French-spec bikes were limited to 100PS or something like that, but I had thought that emissions specs (e.g., catalytic converters) had been standardised since around 2000 for all European models. There are also sometimes minor lighting differences between markets. Sorry I can't be of more help; someone with more direct experience of 6th gens in Europe should know more of the details. Ciao, JZH
-
I've got a simple "Sealey" manual tyre changer in the UK (probably the same as many others coming out of the same factory in China!) and it works absolutely okay. However, I bought a separate, nylon enhanced tyre bar off eBay which works better than the original all-metal one the Sealey came with. What made the unit work best for me was to bolt it to the driveway, using stainless steel button head bolts (slathered in anti-seize) threaded into Rawlbolts sunk into the drive. When I'm done I unbolt it and put the bolts back into the holes. So far, so good! Ciao, JZH
-
Also not from waaayyyy back, but still pretty far back. I was both exhausted and satisfied after completing a SaddleSore 1000 ride just outside Boulogne, France, in around 1998. I think the photo was originally a 35mm slide (which I was still using--and explains why I have several boxes full of slides and few digital photos from the early days!) The FL was my original 1990, bought new in California. Retired it after 60,000 mi or so, but it could have gone on and on (if I had replaced the cam shaft I broke whilst improperly tightening the cap bolts...). Ciao, JZH
-
Mine appeared to be good. The switches are essentially open mechanisms looking up, so all sorts of things will have fallen and washed into them over 22 years. The other way to check this is at the starter harness plug for continuity. You don't need to remove the fairing, it's by the battery under the saddle. A voltmeter will tell you if the circuit is truly open when either of the switches is open, and closed when they are both closed.
-
Can you unplug the R/R run the engine, is there any change to the Ignition Switch operation? Grasping at straws a little now. - Suggest accessing the Ignition Switch 4P plug and do some continuity checks confirming good Switch operation. Refer bottom left corner of wiring diagram for Switch Connection Table. I'm struggling to relate your symptoms to the wiring diagram, also struggling with what or how a wiring modification could induce such strange issues with two separate switch functions.
-
Bloody hell! Now I'm really confused, this is crazy. Check for Non OEM wiring. Are you able to get any feedback from the previous owner as to wiring changes or anything done electrically to the bike?
.thumb.JPG.d5f9f3254e93aa21cc9838c8de0dada2.JPG)
-
Blogs
-
- 122
entries - 565
comments - 289447
views
Recent Entries
Latest Entry
The Last Day Of Good Riding Weather
Juniper Pass
I took a day off from work and also from my bicycle training to take out the Veefalo one last time before the weather turns ugly, supposed to snow the rest of the week and possibly start sticking to the ground along the Colorado Front Range. I took a leisurely pace up hwy 105 toward Morrison and got reacquainted with the bike since its been over a month since I took any sort of twisties on it at all, hwy 105 is a scenic ride along the front range between Denver and Colorado Springs, its mostly easy fast sweepers and lite traffic so its a favorite road of mine when going north. Then I have to negotiate a bit of traffic near Highlands ranch and up hwy 470 into the mountains. I decided to take the Morrison Exit and try either Lookout Mountain or head up Golden Gate Canyon - this time it was Lookout Mountain, I was sort of making it up on the fly as I went along. Lookout Mountain is my old bicycling haunt from my days while I was working at Coors, its a killer ride and all uphill - I don't think I could do it today If I had to, not quite there yet! I saw a whole bunch of riders doing it though and wished I was in shape enough to be there doing it as well. 30 more lbs and I will be able to do it! On this day I would do it on the Veefalo instead.
Â
Â
Â
Â
I took a video from the gateway to the top at the Lookout Mountain State Park, getting past riders, the guy in the green jacket actually pretty much astounded me with how far he had gotten in the short time it took me to set up my camera, some 3 miles at least and up to the gateway from the turn off at hwy 6! Amazing I thought. I took the first two turns slow then got more comfortable as I went up further, till I was doing well, I made some gearing mistakes and took the tight 15mph marked hairpins in the wrong gear so I lugged it a bit on one or two. Still enjoyed it though and then got off at the top and hiked over a rock outcropping for an overview of the road for the pictures below.
Â
Â
Lookout Mountain - Golden Colorado
Zoomed in
Lookout Mountain Park top of the mountain
From there I headed up interstate 70 to Idaho Springs for a beer at the Tommy-knockers brewery, I was the only customer in the joint - slow day for them so they treated me like a king! I got a nice tour of the place sort of impromptu, they made me a nice Pastrami sandwich on rye and with the brown ale it was fantastic. I must say the beer is much better there than in the bottles - its always good at the brewery. I am glad I stopped
Tommy-knockers Brewpub Idaho Springs
Idaho Springs Colorado
Mashtuns and fermenters
Rows of fermenters
I finished my lunch and since the road to Mount Evans is right there I headed up Squaw pass hoping to get in some nice pictures I wasn't expecting what I found, ICE IN ALL THE SHADY PARTS
Icy patches on Squaw Pass definitely taking it easy on that road
There were some section where the ice covered the whole road for 300 yards or so I had to roll through it with my legs out to help keep the bike from sliding and falling over, I took it real slow. A Ford pickup was right behind me so I pulled over to let him pass but the guy was going slower then even I was so I pressed on - in places where I could see I just cut over to the oncoming lane and out of the ice where the sun was shining on the road more, but some places there was not alternative so I just had to go slow, good thing it wasn't slick but rather they tossed some gravel over the worst parts so I had some traction!
I did stop for pictures in all the best spots
Echo Lake at Mount Evans showing off my new plate
Elephant Butte Park and Denver
Close up
Veefalo on Squaw Pass
Juniper Pass
Juniper Pass
Mount Evans
My route A is home B is Tommy-knockers
Â
- 122
-
- 8
entries - 77
comments - 31335
views
Recent Entries
Latest Entry
I Am Back !
Not that it matters and not that I expect anyone had noticed, but to those who sent me "where are you?" I would like to say I am back. Not only that I am officially returning to VFRD after nearly 2 months break but I have also ridden my Hawk last weekend and had FUN! Let me restate that; I had major fun riding! Something I have almost given up on.
Most of you have been riding your whole adult lives and riding is not only a hobby to you, it is part of you. But I started riding three years ago and even though I have encounter some setbacks, till this spring I loved riding with whole my heart. However, I have always considered riding as my hobby. As a hobby which suppose to make my life better, more fun and more rich. Life is too short to do something which we don't fully love.
My love of riding received a first major scar this spring: I lost a friend on the racetrack. He was a total stranger who offered me his help after I lowsided at CMP track last year. I still remember hearing his "Hi, my name is Todd, do you need help?" while I was duct-taping my roadrash from ripped jacket. He helped me straighten up the shifter and we kept in touch. The next time we saw each other was the day he died.
With 9 months delay, I can say that Todd's death shook me more than I have realized. It rooted fear in me which was fueled by seeing and hearing about others getting hurt over and over again. If I was to summarize this year - it would be one big accident report. I became sensitive to every broken bone, every roadrash, every lowside. And even though I did 10 track days this year, I became slower and slower and slower. Suddenly, I have acquired this 'grandma' riding style on the road, frozen with fear that behind every corner there is car standing in my lane, or major sand trap or deer staring at me ... I was crippled with fear not only for me about also for my fellow rider.
So, at the end of this year, I rode more and more by myself. I could not bear the feelings of responsibility for others on the road and my lines were crippled by my own fears. It all culminated this fall at WDGAH. In a freaky accident Love2rideh82crash was taken down by a truck crossing into our lane. I was done. I finished the weekend, locked the VFR into a garage and took a break.
Until the last weekend, I pretended that motorcycles do not exists. As a last instance after 2 months break from riding, I decided to go to CMP track to see if I can still have fun. I also felt like I should go for the memory of Todd. I went and I had fun! I had much more fun than I expected and the most fun on track I can remember. Suddenly the whole track connected into an uninterupted line of turns and I felt one with the bike riding around! I was giggling like a little girl in my helmet and keep on giggling ever since
Granted I was not the fastest one and through out the weekend, I have never exceeded about 60% of my riding abilities, but I had no "oh-shit" nor 'blond' moments. I could have maybe go faster, I could have brake later for the turns and I could have lean further, but I am no Rossi nor Stoner. I decided to ride for fun and I had amazing blast riding well within my comfort zone.
I was proud of myself when, after bandaging Ricks arm, I was able to distance myself and go back to riding without the year-long fear. I did feel bad for him but the feelings were not crippling my lines nor my mind. And when a total stranger came to me and said "Hi, my name is Todd", my heart stopped for a minute though but I suddenly knew that my life went a full circle. I probably will never win MotoGP :idea3: , but I am back! :wheel:
- 8
-
-
VFRD Mission Statement
For owners of the Honda Interceptor and related Honda V4 motorcycles, for the purpose of mutual help concerning safe riding, maintenance, and performance of their motorcycles.
Contributions - VFRD is a member supported website with no commercial advertising
-
Forum Statistics
-
Total Topics25.6k
-
Total Posts354.8k
-
-
Who's Online (See full list)
-
Member Statistics
-
Upcoming Events
-
Latest Classifieds
-
-
Top Downloads
-
-
Popular Contributors
-
Blog Statistics
-
Total Blogs116
-
Total Entries345
-
-
Gallery Statistics
-
Blog Entries
-
-
Blog Comments
-
-
By interceptor69 · Posted
Oops. I do believe I know how to post YT videos or they wouldn't be on YT. However I may have screwed up copying the link to the playlist. Thanks for the helpful comment. -
I think that you might not know how to post videos. You're in your YT studio in these links. You need the link to the actual video. -
-
-
-
Most Contributions
-
