Jump to content

How to remove carb diaphragm from 4rd gen?


Recommended Posts

Hello I need to replace the carbs diaphragm of my RC36 4th gen, to install new ones I bought, but I can't remove the old ones. Can you tell me how to  do it? 

16217921658092486567456272113841.jpg

Link to comment
Share on other sites

  • heiwaz changed the title to How to remove carb diaphragm from 4rd gen?
  • Member Contributer

heat up slides in cup of super-hot water (90-C) for 30-seconds.

 

Grab diaphragm with 2 hands on opposite sides.

 

Pull diaphragm apart in opposite directions.

 

Keep on pulling until you see gap develop between diaphragm and slide.

 

Pull upwards on diaphragm on side with gap and peel off diaphragm from slide.

 

 

Link to comment
Share on other sites

2 hours ago, DannoXYZ said:

heat up slides in cup of super-hot water (90-C) for 30-seconds.

 

Grab diaphragm with 2 hands on opposite sides.

 

Pull diaphragm apart in opposite directions.

 

Keep on pulling until you see gap develop between diaphragm and slide.

 

Pull upwards on diaphragm on side with gap and peel off diaphragm from slide.

 

 

I could remove it, but how to insert the new one? I tried and is very difficult. Should I heat it with water too?

Link to comment
Share on other sites

  • Member Contributer

Yes heat with hot water for 30-sec.

 

Trick to getting on is same in reverse. Grab opposite sides of diaphragm and pull apart.

 

Note that hole becomes slit which is wider than diameter of slide. 

 

Slide slit forward over slide so bottom of slit slides into groove.

 

Keep diaphragm pulled apart and saw laterally to drive into groove.

 

At same time, move diaphragm forwards and continue over slide's groove.

 

Once entire diaphragm has been slid over slide, rotate it about 30-60 degrees in each direction to fully seat in groove.

 

If that didn't make sense, I can take some photos or make video.

 

 

Link to comment
Share on other sites

I think understand more less your explain, but I'm not sure I can be insert diaphragm completely in the gap and once inserted can be rotate well to adjust at correct position. Maybe a video or photo will help me a lot. Thanks for your reply

Link to comment
Share on other sites

12 hours ago, DannoXYZ said:

Yes heat with hot water for 30-sec.

 

Trick to getting on is same in reverse. Grab opposite sides of diaphragm and pull apart.

 

Note that hole becomes slit which is wider than diameter of slide. 

 

Slide slit forward over slide so bottom of slit slides into groove.

 

Keep diaphragm pulled apart and saw laterally to drive into groove.

 

At same time, move diaphragm forwards and continue over slide's groove.

 

Once entire diaphragm has been slid over slide, rotate it about 30-60 degrees in each direction to fully seat in groove.

 

If that didn't make sense, I can take some photos or make video.

 

 

I have broken 2 diaphragm trying to insert it 🤦‍♂️. One of them almost insert it completely. I heath it with water and stretched to get thinner, but if I stretched to much it broke. 

Link to comment
Share on other sites

  • Member Contributer
15 hours ago, squirrelman said:

jbm (jdm ?) supplies those parts, and i believe they will install them if you require so contact them.


Theres NRP who sell them fitted or loose https://nrp-carbs.co.uk/

Link to comment
Share on other sites

  • Member Contributer
On 5/24/2021 at 12:43 PM, heiwaz said:

I have broken 2 diaphragm trying to insert it 🤦‍♂️. One of them almost insert it completely. I heath it with water and stretched to get thinner, but if I stretched to much it broke. 

Don't stretch too much. Just enough so length of slit = diameter of slide's groove.

Link to comment
Share on other sites

7 hours ago, DannoXYZ said:

Don't stretch too much. Just enough so length of slit = diameter of slide's groove.

If I don't stretch too much is impossible to insert in gap because I need to get thinner stretching them. 

Link to comment
Share on other sites

  • Member Contributer
20 hours ago, heiwaz said:

They don't sell. In price appear to call them for 4th gen 


What did they say?

Link to comment
Share on other sites

maybe send your vacuum slides to danno for diaphragm replacement as he seems quite competent and has the necessary experience.

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

×
×
  • Create New...

Important Information

By using this site, you agree to our Privacy Policy.