Hi everybody! I’ve had tons of people tell me I should post this this on the VFR forums, so here you go!
VFR800 Gear Indicator Bracket.
These brackets are designed to replace the black plastic ring on the key cylinder of a 2002-2009 Honda VFR800 (Non-HISS). It is designed to house a Healtech Gear Indicator, and a USB Charger port or volt gauge. It requires removal of the two screws, and then simply remove and replace the ring with this one, then install the new stainless allen screws (included).
PLEASE SPECIFY COLOR, THE SUDE THAT YOU WANT THE GEAR INDICATOR ON, AND WHETER OR NOT YOU WOULD LIKE IT WITH THE BUTTON HOLES, OR WITHOUT WHEN ORDERING.
I can make them without the buttons as well (see my listing for F4i Charger Bracket for photos; it will look the same, but fit the VFR).
There is a wide variety of USB chargers (not included) that will fit this bracket. There are also voltmeters (pictured) that fit. The following link is for the charger that I have used for several years. The same manufacturer makes the voltmeter, and they are all available in a variety of colors.
These brackets are 3D printed from a durable PETG plastic, and I can make them in gray (pictured), black, white, yellow, red, blue, purple, or green. If you want a custom color, please email me and I’ll see if I can make it happen. PLEASE SPECIFY COLOR, THE SUDE THAT YOU WANT THE GEAR INDICATOR ON, AND WHETER OR NOT YOU WOULD LIKE IT WITH THE BUTTON HOLES, OR WITHOUT WHEN ORDERING.
Disclaimer: No 3D printed part is ever flawless. It is guaranteed to fit perfectly, but not guaranteed to be without minor cosmetic defects. For examples, please examine the photos carefully. That part was installed right off the printer and is representative of a typical part.
VFR VFR800 Honda Motorcycle USB Charger phone charger gear indicator
Question
Adam1krr
Hi everybody! I’ve had tons of people tell me I should post this this on the VFR forums, so here you go!
VFR800 Gear Indicator Bracket.
These brackets are designed to replace the black plastic ring on the key cylinder of a 2002-2009 Honda VFR800 (Non-HISS). It is designed to house a Healtech Gear Indicator, and a USB Charger port or volt gauge. It requires removal of the two screws, and then simply remove and replace the ring with this one, then install the new stainless allen screws (included).
PLEASE SPECIFY COLOR, THE SUDE THAT YOU WANT THE GEAR INDICATOR ON, AND WHETER OR NOT YOU WOULD LIKE IT WITH THE BUTTON HOLES, OR WITHOUT WHEN ORDERING.
I can make them without the buttons as well (see my listing for F4i Charger Bracket for photos; it will look the same, but fit the VFR).
There is a wide variety of USB chargers (not included) that will fit this bracket. There are also voltmeters (pictured) that fit. The following link is for the charger that I have used for several years. The same manufacturer makes the voltmeter, and they are all available in a variety of colors.
These brackets are 3D printed from a durable PETG plastic, and I can make them in gray (pictured), black, white, yellow, red, blue, purple, or green. If you want a custom color, please email me and I’ll see if I can make it happen. PLEASE SPECIFY COLOR, THE SUDE THAT YOU WANT THE GEAR INDICATOR ON, AND WHETER OR NOT YOU WOULD LIKE IT WITH THE BUTTON HOLES, OR WITHOUT WHEN ORDERING.
Disclaimer: No 3D printed part is ever flawless. It is guaranteed to fit perfectly, but not guaranteed to be without minor cosmetic defects. For examples, please examine the photos carefully. That part was installed right off the printer and is representative of a typical part.
VFR VFR800 Honda Motorcycle USB Charger phone charger gear indicator
https://www.ebay.com/itm/125527979784?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=z6UO-uFgTjG&sssrc=2349624&ssuid=z6UO-uFgTjG&var=&widget_ver=artemis&media=COPY
Link to comment
Share on other sites
5 answers to this question
Recommended Posts
Archived
This topic is now archived and is closed to further replies.